Models
>
ZDT870SPF1SS
ZDT870SPF1SS General Electric Dishwasher - Overview
Sections of the ZDT870SPF1SS
[Viewing 7 of 7]
Keep searches simple, eg. "belt" or "pump".
LOWER RACK ROLLER
PartSelect #: PS16217024
Manufacturer #: WD12X26146
This is a lower rack roller for your dishwasher. It attaches in the lower roller assembly on the bottom of your rack to allow the rack to smoothly slide in and out. This replacement part is 1.5 inches...
$13.13
In Stock
Door Latch
PartSelect #: PS6447681
Manufacturer #: WD21X10490
This is replacement door latch for your dishwasher. The door latch is attached to the tub frame, and connects to the door strike to keep your dishwasher door closed during operation. If you have a bro...
$44.23
In Stock
Flood Switch
PartSelect #: PS8690623
Manufacturer #: WD21X10519
This is a flood switch assembly for your washer. The flood switch controls the hot and cold water filling your washer tub to ensure the proper amount of water. You may need to replace this part if you...
$53.93
In Stock
Countertop Bracket
PartSelect #: PS11700868
Manufacturer #: WD01X21740
This mounting bracket is manufactured to secure your dishwasher to your countertop. Mounting brackets should be installed so the dishwasher doesn’t tip forward. You can fit the bracket to either the c...
$7.49
In Stock
Leveling Screw
PartSelect #: PS11762951
Manufacturer #: WD12X23057
This is a genuine GE dishwasher leveling screw. It operates as a leg on the bottom of your dishwasher, and can be screwed in and out to raise and lower the height of the dishwasher. It is made of meta...
$8.06
In Stock
SCR B-16 HXW 1/2 Stainless Steel
PartSelect #: PS2370492
Manufacturer #: WD02X10169
This part is a replacement middle spray arm bearing for your dishwasher. The spray arm bearing reduces friction and allows the spray arm to rotate during the operating cycle. If the spray arm is not r...
$13.88
In Stock
Screw - 8-18 B HXW .480 S
PartSelect #: PS2337849
Manufacturer #: WD02X10160
This is a genuine hex head screw replacement, designed for use with dishwashers. Most of this type of screw is used to hold the kickplate in place on the bottom of your appliance. This screw is sold i...
$8.06
In Stock
Questions And Answers for ZDT870SPF1SS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the ZDT870SPF1SS
[Viewing 10 of 10]Will Not Start
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Not drying dishes properly
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Will not dispense detergent
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No water flowing into dishwasher
We tried cleaning out the filter and it clogged with a huge amount of gunk. We removed the gunk, scrubbed the filter, and tried running the dishwasher, but still no water. That took over an hour (not counting the time the dishwasher spent running). Then we tried your diagnosis center and it pointed to the flood switch or the water valve.
... Read more
I extracted the flood switch (another 30-60 minutes) to check it, and it also contained gunk and (significantly) did not rattle, which made me suspect the flood switch was the problem, so I ordered one. Once the replacement arrived, I checked it and the flood switch rattled, confirming that it should work properly. I spent 30-45 minutes installing it, plus the filter assembly and racks I had to remove to access it. Ran the dishwasher and everything came out sparkling clean. I don't know where the gunk came from, but if you aren't getting water and the filter is full of gunk, check the flood switch.
Read less
Parts Used:
-
Jeff from AUBURNDALE, MA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
32 of 38 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door latch not functioning
1. Turn off breaker supplying power to dishwasher in electrical panel
2. Open dishwasher door
3. Unscrew the screws that secure the dishwasher to the counter.
4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch.
5. ... Read more On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside.
6. Remove old door latch.
7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in.
8. Plug wire harness into new door latch.
9. Re-align dishwasher and re-secure to counter in previous position.
10. Test latch to make sure it closes properly.
11. Turn on breaker in electrical panel.
The dishwasher should now function properly.
2. Open dishwasher door
3. Unscrew the screws that secure the dishwasher to the counter.
4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch.
5. ... Read more On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside.
6. Remove old door latch.
7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in.
8. Plug wire harness into new door latch.
9. Re-align dishwasher and re-secure to counter in previous position.
10. Test latch to make sure it closes properly.
11. Turn on breaker in electrical panel.
The dishwasher should now function properly.
Read less
Parts Used:
-
James from ALBRIGHTSVLLE, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
24 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heating Element Wasn't Turning On So Dishes Weren't Drying
Ran the diagnostic code test and no alarms turned on. Ran the heater test and it didn't turn on. I figured it was either the flood switch or the heating element itself. Removed and cleaned the flood switch and still nothing. Replaced the old flood switch and now it works like a charm. It took a minute to run tests and figure out a pl
... Read more
an of action, but after ordering and receiving the part it was a quick operation to replace the old flood switch. Kill the power. Remove lower basket. Remove lower arm. Remove the coarse filter and the fine filter. Dry up water in bottom of dishwasher. Use 1/4" nut driver to remove two screws holding flood switch in place. Unplug old switch. Plug in new one. And put everything back. Saved a few bucks for sure. If I can do it, you can do it!
Read less
Parts Used:
-
Cheyne from RIVERSIDE, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
15 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!