Quick Question!

Have you ever purchased from PartSelect.com before?

Models > YE20FY1 Maytag

YE20FY1 Magic Chef Dryer - Overview

Get Parts and Repair Help for YE20FY1

If you know the dryer repair part you need, you can browse the list of all parts on the YE20FY1, or you can search by name or part description. You can also find your part by where it is located on the YE20FY1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for YE20FY1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the YE20FY1

[Viewing 3 of 3]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.56

Multi Rib Belt - 92-1/4"

This multi rib belt is an important part in your dryer, it is what helps rotate the drum. The belt attaches to the drum, idler pulley, and motor pulley. As the armature of the moto...

$43.29

Heating Element Kit - 240V 4750W

This dryer heating element kit is 240 volts and 4750 watts. The kit comes with a high limit thermostat of L248-80. The function of the heating element is to produce the heat that allows you to dry your clothing during your dryer cycle. If your clothes take too long to dry, or if your dryer is not getting any heat or enough heat, you may need to replace your element. Before you begin your repair, make sure to disconnect the power from the dryer. The tools you will need for this repair include a putty knife, a quarter-inch nut driver, and a pair of needle nose pliers.

$2.96

Screw

This screw is sold individually.

$50.03

Rear Drum Support Roller Kit

The rear dryer drum roller functions by holding the drum in place while the drum rotates on support wheels during the drying spin/tumble cycle. Included in this rear drum support roller kit are four screws, one spacer, two washers, two retaining rings, two rear rollers, and two cylinder support shafts. The drum support roller kit may need to be replaced if the dryer is noisy or will not tumble. Important note: This kit has been updated by the genuine manufacturer to have one spacer that is the thickness of two spacers. Please search by model number to get these parts separately.

$5.67

Blower Wheel Clamp

This blower wheel clamp, used in a clothes dryer, is a clamp that holds the blower wheel to the motor shaft. This part helps hold the blower wheel in place to function easily and p...

$15.82

Rear Drum Support Roller

This rear drum support roller stabilizes the dryer drum and holds it in place during the drying cycle while the drum rotates on the support wheels. If your dryer is making loud squeaking or thumping noises, or the dryer will not tumble, there could be an issue with your rear drum support roller. If you can see that the roller is damaged, you should replace it right away. The repair is relatively easy, and takes between 15 minutes and 1 hour to complete. This drum support roller works with electric or gas clothes dryers, is sold individually, has an outside diameter of about three inches, and comes with a bearing.

$21.92

Thermal Fuse

$44.71

High Limit Thermostat (Limit: 258-80)

This high limit/safety thermostat is used on many gas and electric clothes dryers. It is made of metal, and is almost two inches long. With this thermostat, a dryer's heating element will cut out if the internal temperature reaches 258 degrees Fahrenheit. The element will kick back in when the temperature drops to 178 degrees Fahrenheit.

$5.10

Timer Resistor Assembly

This timer resistor assembly is two inches long. It is made of ceramic and metal.

$11.84

Drum Glide and Cushion Kit

Pad has adhesive backing.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dry stopped heating - still had good air flow

  • Customer: Brianna from Littleton, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 180 of 205 people found this instruction helpful
I was about to purchase a new dryer because of the age of my dryer and not wanting to hire someone to fix it. After a little web research, I saw several do-it -yourself stories indicating this was a very easy repair.

This was an extremely easy repair and it save me lots of $$:
(1) Disconnected power
(2) Opened the top of the dryer
read more

broken tumbler belt

  • Customer: Michael from San Antonio, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 102 of 107 people found this instruction helpful
1. Removed the screws from the lint catcher
2. Removed the bolts from upper rear of dryer
3. Pried off the dryer top from the front (it rests on rear hinges)
4. Disconnected dryer door wiring
5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall when it loses suppor... read more

Dryer squeaking really badly

  • Customer: Michelle from Kirkwood, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 64 of 65 people found this instruction helpful
I opened the dryer from the front by pushing in on the two clips just under the top. I then had to remove two screws on each side and took the front panel off. I reached around underneath on the right side to slip the belt off the pulley. I pulled the drum out and then I could see the roller that was squeaking (the left one). The wheel had sheared some o... read more