WWA5411BAL General Electric Washer - Instructions

This was a very easy repair. First I unpluged the 120VAC power cord. Then I turned the water off. Next I opened the hose connections. Then I removed 3 screws from the back which exposed the Inlet Valve. I removed the old valve taking note of where the wires went. Then I installed the new one. It took less than 10 minutes!

removed old knob pushed on new nrw one locked on wifh key

Removed back cover. Opened top lid - slid putty knife under front lip to release latch (2). Removed old valve hose and clamps. Replaced with new valve hose and new clamps. No more leaking during fill.

Took off the backing and then the water inlet piece and just reverse the procedure when installing the new part. What really amazed me was the ease of ordering the part through this website. I found it, ordered it and in two days it was here!! Great website, you folks really know what your doing. My repair was under 25 dollars, how much would have I paid for a service tech to come out, don't even want to think about it !! I'm telling everyone I know about your website. THANKS AGAIN !!!!!

Removed existing knob by using pliers to release clip from shaft. Inserted new knob (with clip attached) onto shaft and aligned with shaft groove to engage clip. Easy breezy.

Since the valve sprayed water out in one particular spot, it was easy to determine what part I needed. After I received the part from "Part Select" it was super easy to replace and took about 10 min. and the washer was good as new.

Unplugged washing machine from electrical outlet. Turned off water supply to washing machine. Removed inlet hoses. Removed 2 screws to get panel off that water valve attaches to. Removed the panel for access to water valve. Removed fill hose from water valve and then unbolted valve from panel. Made diagram of electrical wiring to ensure correct placement on new valve. Attached new water valve, electrical wires and fill hose to valve. Installed panel in machine and hooked up inlet hoses. Turned on water supply and inspected for leaks. Turned on washing machine to verify filling and repair was OK.

Replaced the water inlet valve. Your shipping was next day the best I have ever received. Thank You

Very straight forward install. First removed the agitator itself by pulling straight up on it. Then removed the agitator coupling without the need of any tools just pull it straight off. Install new coupler and agitator.

An older gentleman neighbor needed help finding a part for his machine. We checked local parts stores to no avail. I researched the internet, found your site and ordered the part. My adult son put the part on in less than 15 minutes. Our neighbor was very happy. We will tell any one in our neighborhood to order parts here. We followed the part watching UPS. The part arrived at the exact day and time. It couldn't be easier.

Once I figured out what was wrong (splined, hard rubber part of the agitator coupler had parted from the inner, metal part)the job was easy. But I couldn't really tell what was going on until I saw the new coupler ($31.25)which I didn't even have to use. What I did was rough the outside of the metal core with a coarse file, score the inside of the outer, hard rubber part with a screw driver, clean both surfaces thuroughly and reassemble with JB weld. Let sit for 24 hours, and voila. If I had to do it again I could do it in half an hour (not counting glue set-up time).

quck delivery thanks. removed back panel and valve assembly. replace unit,and replaced panel. yep it works

Using the 1" putty, push in on the 2 clips holding the top of the washer. Lift top, exposing the top of tub. Remove old rubber seal from top edge of tub. To ease installation of new seal, stretch it over the edge of tub which tensions it, then start tucking the outer lip along the outside edge, tilting the seal towards the outside edge until the seal is completely in its groove all around. I had to hold down on the seal to keep it from rolling off while I lowered the top back down. When the lid is down, push hard to engage the 2 clips that lock it down.

Unscrew the back cover to washer, Find 3 hole plug, plug in the cord, take the ground wire and screw it to the screw next to the cord that is screwed into the metal frame, put the back panel on and that's it! easy peasy! Remember to hook up your water hoses and turn on the water to check for leaks BEFORE plugging it in! Very Easy!

In my case, the splined shaft (steel) had worn off all splines in the aluminum coupling. So the spin cycle would eventually get enough friction to spin the clothes, but the friction required to agitate the clothes back and forth was too much. Since the splines were worn off, the whole agitator lifted right out with no tools. There is a cap on the top that needs to be kept in good condition, so be careful popping it off. After removing the cap, I cut a hole using a utility knife, then punching a flat head screw driver around the edge. Careful not to damage the edge that the cap seats to. I then matched a socket the size of the top of the coupling and hammered the coupling through the bottom. I used the flat blade also to clear the aluminum out of the splines on the shaft. The fit of the new coupling into the agitator is tight. I put the coupling in the freezer, and the top of agitator in hot water to help resize things for installation. I also used dish soap on the coupling straight out of the freezer. A small amount of grease should be used on the shaft to make it easier and prevent galvanic corrosion. It still took all my weight to install. Don't use a hammer, as you don't want to damage the area the cap goes on. Pop the cap on and wash.