This part is known as a pulsator cap or washplate cap, and is designed for your LG washer. It fits over the washplate mounting bolt and prevents clothes from getting caught on the washplate during a w...
$30.01
In Stock
Order within the next 7 hrs and your part ships today!
This drain hose is a genuine OEM replacement part supplied by LG for use in their washing machines. It is a light gray pipe with a diameter of 1.25 inches. The drain hose is connected to the drain pum...
$36.10
In Stock
Order within the next 7 hrs and your part ships today!
This water-level pressure switch in your wash monitors and regulates the water levels throughout the fill, wash, and rinse cycles. You will usually find it inside the control panel or near the tub. It...
$49.27
In Stock
Order within the next 7 hrs and your part ships today!
This inlet valve assembly in your washer controls the flow of hot and cold water into the machine, opening and closing as needed during the wash cycle to ensure the drum fills with water at the correc...
$110.56
In Stock
Order within the next 7 hrs and your part ships today!
Order within the next 7 hrs and your part ships today!
Questions And Answers for WT7150CW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Chad
December 6, 2023
My washer is not draining completely and I get an OE error code. I pulled the drain pump and it wasn’t clogged or blocked. I checked the hoses and there are no blockages. I reinstalled the pump, still didn’t work. I replaced the pump, still have the same problem. I reset the washer and I ran the diagnostic tests. The test gets stuck on T5 and then starts making a singing sound until I shut it off. The drum spins during diagnostics, but when I run it normally, the spin light will be on but the drum isn’t spinning. None of this makes any sense and any help is appreciated!
For model number WT7150CW
Hello Chad, thank you for your inquiry. According to our research, the OE error code indicates that the washer is experiencing a draining problem. As you have already replaced the drain pump and checked the hoses, we would recommend replacing the electronic control board, part number PS16551768, to fix the issue. It manages the washer's functions such as filling, washing, draining and spinning. We hope this solves your problem!
Does the Pulsator cap need to be removed in order to pick up extraneous items /debris?
the CL code fix is not specific enough.
Electric connect is ok; circuit breaker is ok..... what's going on???
For model number WT7150CW
Hello Gerald, thank you for your inquiry. According to our research, you may need to remove the pulsator cap if you want to clean the wash plate. The error code CL indicates that the control lock function is activated. Press and hold the extra rinse button for 3 seconds to deactivate this function. We hope that helps!
Was this helpful?
Thank you for voting!
Alex
March 3, 2024
Can I swap the agitator for an impeller?
For model number WT7150CW
Hello Alex, thank you for reaching out. According to our research, your model does not come with the agitator. We hope this information helps!
Was this helpful?
Thank you for voting!
Buddy
March 30, 2024
Can I buy an agitator for this model? I don't like the peller
For model number WT7150CW
Hello Buddy, thank you for reaching out. You cannot use an agitator in your model as it is intended to be used with the pulsator assembly only. We hope this information helps!
raised the front of washer by hand (literally) and placed two 2x4 blocks under front lip for support. reached up inside washer cabinet and unscrewed the broken leg piece upwards into the cabinet. this was the only way I could get the broken piece out without some specialized tool to reach it from the underside. replacement with the new
... Read more leg was a breeze.
The old dispenser is removed by slightly raising the front as you pull it out of the housing slot. To install the new dispenser, keep the front slightly tilted up and insert the new dispenser into the housing alot
