WRT8G3EWM Crosley Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
broken retainer bar
super easy snaps Into place in a matter of seconds I wish I would have done it a long time ago
Parts Used:
-
christina from norman, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Old gasket was torn causing excessive moisture in refrigerator.
Removed door, removed old gasket, cleaned surfaces where gasket sealed, replaced gasket, re-installed door. About 10-15 min.
Parts Used:
-
Joseph from Cape Coral, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
not cold enough
per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section
Parts Used:
-
Gary from Hudson, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
drawer support rail broke just behind the front of the rail.
Unloaded the shelf and removed shelf. unscrewed the one screw and removed the rail. inserted new rail and replaced the screw. DONE.
Parts Used:
-
William from Buckeye, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
both retainer bars broke within the first year..
The new ones popped right in no problems
Parts Used:
-
George from Highland, KS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The freezer door shelf retainer bar was broken
1.) Removed the old broken freezer door retainer bar. 2.) Removed the new freezer door retainer bar from shipping carton. 3.) Inserted new freezer retainer bar into place. 4.)Done is less than 4 minutes.
Parts Used:
-
Charles from Dimmitt, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Shelf was broken
-
Gay from Carlsbad, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Fridge section not cold enough, Frost in freezer
-
Paul from Hicksville, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Original plastic hinge cracked across the middle
Removed 2 hex screws & old hinge, placed new hinge on cabinet & found that it didn't fit; one hole was about 1/8" off. Had to drill a new hole in cabinet top in order to attach new hinge. Hinge works fine now. I'm glad to find the hinge is metal; original one was plastic.
Parts Used:
-
Al from Sarver, PA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
warm fridge, cold frosty freezer
remove food, then the shelf, then use a hot air gun to defrost and loosen the back panel, then remove the panel, then defrost the coil and thermostat area. using wire tools, replaced the defrost thermostat,and re-assembled freezwr and test
Parts Used:
-
Jim from AuSable Forks, NY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Torn Gasket
Pulled the old one off, pressed new one into groove on door. First time it really was as easy as the instructions on line said.
Parts Used:
-
Richard from Fruitland Park, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Light Would Not Come On.
I removed the four bolts holding the light switch and temp knob with a nut driver, unplugged the unit and moved it to the table top. I removed the switch and replaced it with a new one. I plugged the unit back in and drove the four screws in with a nut driver and the light now comes on when I open the door. Real simple!
Parts Used:
-
Grant from Apache Junction, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
The handle broke.
-
Shakima from New York, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Door shelf retainer bar broke from to much pressure on it over the years
-
Linda from Newport, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Right rail broken
removed drawer removed upper shelf turned upside down unscrewed old one installed new one put shelf back in put drawer back in done super easy
Parts Used:
-
Patrick from Wolverine, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!