Parts That Fix Whirlpool Refrigerator WRS325FDAB06 Leaking
Leaking is a commonly reported symptom for the WRS325FDAB06 Whirlpool Refrigerator, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your WRS325FDAB06 Whirlpool Refrigerator that will fix Leaking. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
This is the replacement water tube kit for your refrigerator. This tubing is made of plastic, is 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the original tube, and may need to be cut. This water tube transports water to the ice and water dispensers. If your refrigerator is leaking, or if the ice and water dispensers are not dispensing properly, you may need to replace this tube. This part is sold individually and is an OEM part sourced directly from the manufacturer.
Replacing your Kenmore Refrigerator Water Tube Kit
Customer Repair Stories
35 year old water tube became brittle and cracked; leaking water
-
Melvin from OPELIKA, AL
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Water began to leak under the refrigerator. Source looked like it was coming from control valve suppling water to ice maker and water dispenser.
-
jesse from hacienda heights, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
This is the replacement evaporator drip tray for your refrigerator. It is made of white plastic and is approximately 19 inches by 9 inches. The evaporator drip tray sits below the evaporator to collect dripping water. If the drip tray is damaged, you may notice that your refrigerator is leaking. Because it is made of plastic, the drip tray can eventually develop a crack. You will need to pull out the refrigerator from the wall, and take off the bottom panel on the back of your refrigerator in order to access the drip tray for replacement. This is an OEM part sourced directly from the manufacturer.
Customer Repair Stories
Water leaking from under refrigerator.
The reason still had leak after initially turning off water supply was because the drip tray is used to catch the water when refrigerator goes into the defrost cycle. Since the original drip tray had cracked, water only appeared on floor after defrost cycle.
-
Ronald from DELRAN, NJ
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set
Cracked Evaporation tray was leaking water on kitchen floor
-
Jerrel from REDDING, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set, Wrench (Adjustable)
Sold Individually. - * Part may differ in appearance, but functions same as original.
Replacing your Whirlpool Refrigerator Water Tube Connector/Union - 5/16 to 5/16
Customer Repair Stories
Leaking water tube connector/union
-
Roderick from NEWTOWN, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Had to replace a hose connector at the base of my refrig/frreezer
When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection.
I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.
LG
-
Leo from Salem, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
This part releases water from the supply line when it's activated.
Customer Repair Stories
Ice maker not making cubes.
-
Robert from STRONGSVILLE, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Water and ice dispenser's were not working
-
Enrique from CASA GRANDE, AZ
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
NOTE: As per manufacture this is no longer a tank. The tank style has been updated with coiled tubing.
Bucket only. All other parts sold separately. This part holds the ice once it's released from the icemaker.
Replacing your Whirlpool Refrigerator Ice Bucket
Customer Repair Stories
Ice bucket cracked and pieces broke off the bottom
-
Elizabeth from SANDY, UT
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Ice bucket had cracked and came apart at the front bottom.
Henry
-
Henry from ROWLETT, TX
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
This is a plastic tubing insert kit for a refrigerator ice maker. This kit includes a package of four tubing inserts. The kit does not include other parts such as the ice maker water fill tube kit or ice maker fill tube gasket, so consider ordering those parts if necessary. The inserts are used with 1/4-inch plastic tubing. The inserts attach on the end of the water tubing to provide a smooth and solid connection between the water tubing and the clamp that attaches the tubing to the water fill valve. This is an OEM part from the genuine manufacturer.
The crisper drawer (Crisper Pan, Refrigerator Crisper Drawer) with humidity control is meant to keep your vegetables and fruit as fresh as possible by allowing you to regulate the humidity levels within the drawer. It attaches on the inside of your refrigerator to the bottom of the crisper shelf. This drawer can break from misuse or accidental damage. It is also subject to material fatigue over time. If broken or damaged, it may be difficult to slide the drawer in and out, and it should be replaced. This plastic drawer measures 14.92 inches long, 7.6 inches high, and 16.5 inches wide and comes in white/clear.
Replacing your Whirlpool Refrigerator Refrigerator Crisper Drawer with Humidity Control
Customer Repair Stories
Drawer guides broken
-
Paula from Chesterfield, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
track of the pan become broken
-
Darrell from Cedar Bluff, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
This is an OEM replacement ice and water filter for your refrigerator. In side-by-side refrigerators, it is found in the top right corner or the bottom left grille. In bottom-freezer refrigerators, the filter is in the bottom left grille. In top-freezer units, the filter is located in the middle of the refrigerator. This NSF certified filter reduces 28 contaminants including pharmaceuticals, metals, minerals, pesticides, cysts, industrial chemicals, Class I Particulates and chlorine. It is made up of coconut carbon block and has three layers of filtration. The first layer is particle filtration that helps block larger contaminants. The second layer is micro-filtration, which prevents medium-sized impurities from passing. The third layer is called absorption filtration, which absorbs microscopic-sized pollutants. It measures 2 inches deep, 2 inches wide, 1-1/2 inches high, and weighs 0.5 lbs. To ensure your filter is working its best, it needs to be replaced every six months. This single filter has a simple, quick-turn installation feature that does not require any tools.
Customer Repair Stories
The refrigerator display said I need to replace the filter.
Upon reading the instructions, I removed the old filter.
When I removed the old filter I NOTICED HOW IT CAME
OUT SO THAT I COULD HOLD THE NEW FILTER IN
THE SAME POSITION AND REPLACED IT WITH THE
NEW IN THE SAME POSITION. When I closed the cover
door, I w ... Read more ent to the display panel and reset water filter display.
-
ronald from SEVERNA PARK, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
no problem. the ice and water need to be replaced every 6 months
-
Patricia from ALAMEDA, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
If you have ice building up in your freezer, or if your freezer is getting too warm during the defrost cycle you may need to replace the bi-metal defrost thermostat. The function of the defrost bi-metal thermostat is to clip onto the evaporator and protect your evaporator from overheating during the defrost cycle. If your refrigerator does not defrost properly you can test both the thermostat and the heater to figure out which part is at fault. For this repair, you will need a Phillips screwdriver, a 1/4 inch nut driver, a flat blade screwdriver, a pair of wire strippers, a roll of electrical tape, and a few butt splice connectors.
Replacing your Whirlpool Refrigerator Bi-Metal Defrost Thermostat
Customer Repair Stories
Auto Defrost Freezer keeps defrosting SIDE BY SIDE KITCHENAID
-James
-
James from Ringoes, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Fridge was getting too warm, ice buildup on coils.
Part Info:
The bi-metal strip is clipped onto the evaporator coils and is designed to regulate the defrost coil temperature. If it is n ... Read more ot functioning properly you may notice ice buildup preventing air flow (and preventing proper refrigeration), or more rarely the freezer side may get too warm during the defrost cycle.
Materials:
* Replacement bi-metal strip
* Wire cutters
* Wire strippers
* Wire nuts
* Electrical tape
* 10MM socket
Steps:
1: UNPLUG THE FRIDGE! If there is ice buildup, wait until the ice has melted. A box fan blowing at the ice will help melt it more quickly.
2: Remove the panel covering the evaporator coils. It's located inside the fridge, on the freezer side.
3: Un-clip the bi-metal strip from the evaporator coils.
4: Unplug the wires from the evaporator fan, defrost coil and bi-metal strip, then disconnect the main connector that is plugged into the rear wall.
5: Clip both wires to the old ( bad ) bi-metal strip. Cut close to the casing of the bi-metal strip so there are long wires to splice onto.
6: Strip 1/4 to 1/2 inches of insulation off of the ends of the wires ( depending on the size of the wire-nuts you use). Twist the bare wires slightly to prevent fraying.
7: Do the same for the ends of the wires on the (new) bi-metal strip.
8: Take the ends of the wires belonging to the (new) bi-metal strip and the wires coming from the main plug. Take the like-colored wires, and twist the bare metal ends together.
9: Twist on wire nuts, for both sets of wires. Make sure they are snug, with no bare wire showing.
10: Tape over the wire nuts with electrical tape. Tape over the wires nuts in a spiral fashion, completely covering the nut and both wires that are now spliced together. This will prevent accidental shorting.
11: Plug the main plug back into the rear wall of the fridge. Also re-connect the connectors to the evaporator fan and defrost coil. Make sure the clips on the connectors are snug to ensure a good connection.
12: Clip the new bi-metal strip onto the coils, in the same spot as before. ( Usually just after the small incoming copper tubing that connects to the coils, known as the expansion valve. That is usually the coldest spot on the coils during operation).
13: Replace the panel that covers the coils.
14: Plug the fridge back in... Now you fridge should defrost correctly. If it does not, your defrost coil could be burned out, or the control board could be faulty.
-
Cathy from Winter Park, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
This manufacturer-certified Refrigerator Door Shelf Bin, also known as the crisper bin and door shelf bin, is made of clear plastic, and is easy to install. It is used to hold items in the fridge door, like jars, bottles, cans, and condiments, and this item is clear with white trim around its top edge and you'll be able to visually see if the part is broken. This particular shelf attaches to the fridge door. You can check if this model is right for your appliance by checking your user manual and model number. This individually-sold door bin fits many different models of side-by-side refrigerator, and can be installed with the use of no tools.
Replacing your Whirlpool Refrigerator Refrigerator Door Shelf Bin
Customer Repair Stories
Not enough door storage
-
Dennis from Owings, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
plastic door shelf was cracked & couldn't hold any weight
-
Nancy from Hilton Head Island, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins