Parts That Fix Whirlpool Washer WFW9470WW01 Will not drain
Will not drain is a commonly reported symptom for the WFW9470WW01 Whirlpool Washer, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your WFW9470WW01 Whirlpool Washer that will fix Will not drain. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
Fixes Symptom 95% of time
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.
$
160.49
In Stock
PartSelect Number PS1485610
Manufacturer Part Number 280187
Replacing your Kenmore Washer Drain Pump Kit
Customer Repair Stories
Water still in tub / tub would not spin
Don't know how they managed to get out of the washer tub, but we found a quarter, dime and penny in the "lint" filter (called the "Cap" in the PartSelect details). The penny managed to get into the impeller and took out 3 1/2 of the 4 impeller blades.
Replacement is very simple, about a 15-20 minute job Be sure the machine is u ... Read more nplugged for safety.Remove the three (3) screws holding the lower front panel and remove the panel. The pump assembly is a white unit about the middle of the opening (the original pump itself was black, the new one is white). Unscrewing the large cap will allow any residual water to drain out (we used a wet/dry shop vac to get most of the water out of the tub first). Following the wires going to the pump, there is a cover over the wiring connector that easily pops up and the connector can be pulled out. Directly below the unit is a screw with a Torx head that has to be removed, then two (2) hoses held with compression hose clamps that need to be removed with pliers. The unit will slide out of the base of the washer. There is a wiring harness in front of this assembly that can be popped loose on one side or the other to get the unit out.
Reversing the steps gets everything back in place.
NOTE: A notice came with my new pump stating that a tab needed to be removed on the wiring connector. It is easily removed by hand.
By the way - that was the most expensive penny I've ever owned! Pockets in jeans are now required to be turned out in our house before they are allowed in the washer!
Replacement is very simple, about a 15-20 minute job Be sure the machine is u ... Read more nplugged for safety.Remove the three (3) screws holding the lower front panel and remove the panel. The pump assembly is a white unit about the middle of the opening (the original pump itself was black, the new one is white). Unscrewing the large cap will allow any residual water to drain out (we used a wet/dry shop vac to get most of the water out of the tub first). Following the wires going to the pump, there is a cover over the wiring connector that easily pops up and the connector can be pulled out. Directly below the unit is a screw with a Torx head that has to be removed, then two (2) hoses held with compression hose clamps that need to be removed with pliers. The unit will slide out of the base of the washer. There is a wiring harness in front of this assembly that can be popped loose on one side or the other to get the unit out.
Reversing the steps gets everything back in place.
NOTE: A notice came with my new pump stating that a tab needed to be removed on the wiring connector. It is easily removed by hand.
By the way - that was the most expensive penny I've ever owned! Pockets in jeans are now required to be turned out in our house before they are allowed in the washer!
Read less
-
Bob from Clayton, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
64 of 69 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not drain ,F02 and SUD code displaying
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.
(3) I packed towels under the washer.
(4) I slowly removed the cleanout i ... Read more n the front of the pump, using the water vac to catch the water as it leaked out.
(5) I removed the wiring to the motor.
(6) I removed the screw that holds the pump in place with a Torx T-20 socket.
(7) I pulled the pump forward so the clamps that hold the drain hose and discharge hose could be removed using the hose clamp pliers. ( they come off much easier then they go back on ).
(8) I tested the pump and found it would run but was making a lot of noise and running slow.
(9) To reinstall start with number (7) and work backwards to number (1) skipping (3) and (4).
Don Kramer
Wichita, Kansas
(3) I packed towels under the washer.
(4) I slowly removed the cleanout i ... Read more n the front of the pump, using the water vac to catch the water as it leaked out.
(5) I removed the wiring to the motor.
(6) I removed the screw that holds the pump in place with a Torx T-20 socket.
(7) I pulled the pump forward so the clamps that hold the drain hose and discharge hose could be removed using the hose clamp pliers. ( they come off much easier then they go back on ).
(8) I tested the pump and found it would run but was making a lot of noise and running slow.
(9) To reinstall start with number (7) and work backwards to number (1) skipping (3) and (4).
Don Kramer
Wichita, Kansas
Read less
-
Donald from Wichita, KS
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Socket set
231 of 243 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 2% of time
This hose attaches to water pump assembly. NOTE: As per the manufacture if the washer has an Eco Ball, it's no longer needed when the new hose is installed.
$
37.52
In Stock
PartSelect Number PS11755212
Manufacturer Part Number WPW10467168
Replacing your Whirlpool Washer Pump Hose
Customer Repair Stories
Worn out hose had a hole it it.
I romoved the front of the washer access panel. I then used the pliers to remove the clamps from the old hose and to replaceit with the new one.
-
Edward from Clinton, MD
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
16 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer leaking
Opened the front panel with 3 crews T-25 or socket wrench. Panel comes off right away.
Look for the leak. Determined it was the hose. Use power pliers to remove the clamp.
The small clamp was easy. The big one I had to use my yoga to get to it. It probably would had been easy from the back panel but moving the machi ... Read more ne requires brute force.
Once the hose was out I found some bra under wires which is what probably punctured the hose.
Removed the front filter and found a bunch of nails.
Assembly was much easier and placed clamps so that if needed it would be a lot easier to remove and replace.
Look for the leak. Determined it was the hose. Use power pliers to remove the clamp.
The small clamp was easy. The big one I had to use my yoga to get to it. It probably would had been easy from the back panel but moving the machi ... Read more ne requires brute force.
Once the hose was out I found some bra under wires which is what probably punctured the hose.
Removed the front filter and found a bunch of nails.
Assembly was much easier and placed clamps so that if needed it would be a lot easier to remove and replace.
Read less
-
Alexander from Miami, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
38 of 43 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time
This hose goes from the drain pump to the back of the washer.
$
26.74
In Stock
PartSelect Number PS11747970
Manufacturer Part Number WPW10003250
Customer Repair Stories
I was getting a sewer smell when the washer drained I did every cleaning technique and didn't solve the problem then I cleaned the inside drain hose and that helped so I replaced the hose and problem solved.
I removed the back panel to access the top end of the hose then I removed the lower front panel to access the lower end of the hose that attaches to the pump. The hose is secured with spring clamps and they were removed with pliers, the panels are secured with screws.
I replaced the hose and reinstalled the panels and I was do ... Read more ne.
I replaced the hose and reinstalled the panels and I was do ... Read more ne.
Read less
-
anthony from EASTPOINTE, MI
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time
This part regulates the temperature of the water in the tub. The sensor is located in the heating element.
$
37.33
In Stock
PartSelect Number PS11755214
Manufacturer Part Number WPW10467289
Replacing your Whirlpool Washer Temperature Sensor
Replacing your Whirlpool Washer Temperature Sensor
Customer Repair Stories
Washer posting a f6 error
This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks
-
Robert from Salt Lick, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
37 of 111 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing the heat sensor following an F-24 Error Notice.
I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" ... Read more into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" ... Read more into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
Read less
-
william from VIRGINIA BCH, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time
$
12.00
In Stock
PartSelect Number PS11747972
Manufacturer Part Number WPW10004260