Parts That Fix Whirlpool Washer WFW9200SQ00 Lid or door won’t close
Lid or door won’t close is a commonly reported symptom for the WFW9200SQ00 Whirlpool Washer, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your WFW9200SQ00 Whirlpool Washer that will fix Lid or door won’t close. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
Fixes Symptom 80% of time
$
168.78
In Stock
PartSelect Number PS11745072
Manufacturer Part Number WP8183202
Replacing your Whirlpool Washer Washing Machine Door Hinge
Customer Repair Stories
Washer hinge casting broke
Removed washer door from washer. Lay door on work bench (table). You need to remove screws from around most of the washer door to remove broken hinge. Install hinge into door frame. Fasten all screws for hinge and door frame. Reinstall complete door assembly onto washer with removed screws. Helpful to have some hold door for ease of
... Read more
alignment. Tools used: 1/4 inch torque #15 bit with 1/4inch nut driver.
Read less
-
Robert from GILBERT, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
10 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not a problem
Unscrewed door screws from washer lifted the door up a little removed door. Unscrewed screws from the glass side and f door remove hinge replaced with new hinge screwed glass door back together. Attached door back to washer screwed screws back in done
-
Theresa from BATESBURG, SC
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
47 of 50 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2 Strike
Fixes Symptom 12% of time
This part attaches to the door and fits into the door lock when the door closes.
$
11.10
In Stock
PartSelect Number PS11755543
Manufacturer Part Number WPW10488048
Customer Repair Stories
Broken Strike on Washer Door - prevented door from latching, and washer would not start
The end of the strike had broken off, and the pictures did not clearly show there was a cross-member at the end of the strike. That crossmember is what broke on the old strike. The strike has only two screws, both requiring a Torx bit (#20, I believe). Unscrew both screws to remove the strike plate. It was a little difficult to get out -
... Read more
it has a curved top to lock into the top slot, but the bottom slides slightly down into another slot. There isn't a lot of room in the opening to slide the strike up and down and get it out. Putting the new strike on is easier - ensure the curved end fits into the slot at the top and slide it up just a bit, push the bottom of the strike plate in, then let it drop right into place, and reinsert the screws. The only problem I had was the strike's holes for the screws are slotted horizontally, so the strike can be positioned across almost 3/8". The latch would not engage the strike the first time, so I had to loosen the screws and reposition the strike a bit. This time it latched, but the fit wasn't quite right, so I adjusted it again to get it where I needed it.
Read less
-
David D from Severn, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 8% of time
$
156.17
In Stock
PartSelect Number PS11745083
Manufacturer Part Number WP8183270
Replacing your Whirlpool Washer Door Lock/Latch
Customer Repair Stories
Washer would not start reliably.
Followed the video on the website. Very easy to replace the part and it fixed the problem. The trickiest part was reinstalling the ring that holds the rubber gasket in place.
-
Andrew from ROCKVILLE, MD
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken door latch
looked repair on you tube followed instructions. took off broken latch. compared to pictures on sites. ordered part. part arrived in 2 days. put part on. suggest using first method quick and easy.
-
Marvin J. from NICHOLASVILLE, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
10 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!