Models
>
WF461ASP
WF461ASP ((XAA)(0003)) Samsung Washer - Overview
Sections of the WF461ASP
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Hex Head Bolt
PartSelect #: PS4205366
Manufacturer #: DC60-40137A
This part is used for the shaft on the rear of the tub and is sold individually. The head bolt is part of the spider arm assembly, and they are generally changed at the same time. If you are replacing...
$11.94
In Stock
Outer Seal Clamp
PartSelect #: PS4218211
Manufacturer #: DC97-04973B
This is an outer seal clamp for the washer door boot of your Samsung washing machine. This clamp tightly seals the boot of the drum within the door of the washer to prevent leaks. This clamp is made o...
$17.35
In Stock
VALVE-WATER;V-0117,NYLON
PartSelect #: PS4209100
Manufacturer #: DC62-30314K
One solenoid valve for hot water
$89.85
In Stock
ASSY FIXER TUB;WV9900M,WV26R9980KV
PartSelect #: PS16224595
Manufacturer #: DC97-14489R
Shipping bolts are installed through the back of the washing machine, and hold the wash tub and basket in place while your washer is being transported. The tub suspension holds the tub correctly in pl...
$65.12
In Stock
PUMP-DRAIN;120V,60HZ,80W
PartSelect #: PS4204640
Manufacturer #: DC31-00054D
This is the drain pump assembly for various models of Samsung washing machines. The drain pump is used to remove any water from the washer after it has completed its washing cycle. If your washer stil...
$125.40
In Stock
Door Lock Switch Assembly;DW-DL72
PartSelect #: PS4205052
Manufacturer #: DC34-00024B
This part is a door lock switch assembly, and it is made to work with your washing machine. The purpose of your door switch is to lock the door of your washer during the washing cycle. This will preve...
$156.52
In Stock
Washer Bolt Assembly
PartSelect #: PS4217876
Manufacturer #: DC97-02412A
Assembly BOLT;SWF-P12,MOTOR/
$13.62
In Stock
Washer Water-Level Pressure Switch
PartSelect #: PS4217080
Manufacturer #: DC96-01703B
The pressure switch senses and controls the water level in the washer.
$93.87
In Stock
Water Valve
PartSelect #: PS4208672
Manufacturer #: DC62-00142G
Three solenoid valve for cold water
$126.82
In Stock
Questions And Answers for WF461ASP
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WF461ASP
[Viewing 3 of 3]Will not drain
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer making noise a snow smoking.
Take pics every step, easier re-assembly. Dismantled washer keeping bolt/screw section removed compartmentalized in a tackle box in the order of removal. Replaced drum support, bearings, seal, old blots. Too much to write but I was able to do it all in about 4 hours once all the parts finally came in.
Parts Used:
-
Samuel from NEEDVILLE, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench set
9 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The water level was lower than normal.
First unplug or turn off thee circuit breaker. Then remove the two screws to the top cover. Slide the cover back about three inches then remove the cover. Next take out the screw to the old sensor. Then unplug the electrical connection by squeezing and the pulling to disengage. Now set the old unit aside. You then grad your eight inch wi
... Read more
re tie and hold the with flat side to the right and just to the right of the screw hole for the bracket is a square hole. Feed to wire tie into the square hole with your left hand then loop down left side of the end of new sensor and back up threw the square hole and tighten with the pliers. Your new sensor will be positioned just like it was mounted to the metal bracket. And pretty ridged. Now connect the vacuum hose and electrical connector.
Read less
Parts Used:
-
Fredric from ROCKMART, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The drain check valve leaked
The part did not fit this model. The flap part fit the hole but the seal ring is too big. I cut 1\4inch out and used super glue the make it small enough to fit and seal the hose. Make sure you only use a drop of glue and keep the seal even and flat so it will seal
Parts Used:
-
scott from DEERFIELD, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!