This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
This is a 120 volt, 60 hertz drain pump assembly for a washing machine. It is a genuine OEM part. This pump helps expel water from the washing machine, and is activated after the spin speed is maintai...
This part is used for the shaft on the rear of the tub and is sold individually. The head bolt is part of the spider arm assembly, and they are generally changed at the same time. If you are replacing...
This is an individually sold front shock absorber designed for use with Samsung dryers. Shock absorbers are used to distribute the weight of the dryer drum evenly and ensure that the different bumps a...
This is an outer seal clamp for the washer door boot of your Samsung washing machine. This clamp tightly seals the boot of the drum within the door of the washer to prevent leaks. This clamp is made o...
Also known as a bellow. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.
$261.92
In Stock
Questions And Answers for WF337AAGXAA
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
1. remove the three screws from the top backside of the top panel 2. push the top panel to the rear 1/8 to 1/4 inch 3. lift/rotate top panel from rear to front, set aside. 4. remove the three wire connectors from latch. 5. use #15 Torx to remove the three screws from the latch. 6. remove and replace part using to
... Read morep opening. 7. reverse order to finish.
I bought a new door lock for 132 dollars (item number PS2037196).
Ultimately you have to get to the inside of the machine where the door lock is located in order to see if you will need this door lock that I bought.
DISCONNECT POWER FROM MACHINE.
First take off the top by taking off the 2 screws on the bac
... Read morek of the machine.
Second take off the control panel, I believe there are about 5 or 6 screws for that. (there's also a screw when you open up the detergent compartment on the bottom left- also, a lever must be pushed in order for the compartment to come off- it MUST be taken off).
Third unscrew the top of the front white plate.. there should be a 5 or 6 screws for that. You don't need to take off the entire front plate.
Finally unscrew 3 screws that hold the door lock in place .. make sure your hands is in the machine- the back of door lock to catch the lock when you're on the last screw.
Gently take out the door lock from the side with the cables attached by holding the white metal door open (it bends).
Try to pull on the bottom of the door lock (its a manual release). If it doesn't release you need to buy a new door lock like I did... if it does release then you don't need a door lock and just reassemble. (Note: You can also try plugging in the machine and THEN pulling down on the manual release. When I tried this the door lock just vibrated and nothing happened so I bought a new door lock.)
If you have the new door lock continue here:
Take out all 3 cables on the old door lock by pressing on the corresponding clips.
Attach the new door lock with the correct cables. Assemble machine back together.
replaced door latch but door would not close had to remove latch assembly and reset the latch in the latch assembly. To reset latch in latch assembly you remove the black plastic only on latch assembly then press the spring down with thumb move the black plastic catch back to the latch position. when you remove the black plastic there is
... Read morefour metal switchs and one spring that you have to pay attention too so remove very carefully.