Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken glass door on front load waher.
Never thought that the glass would break like it did. Removed the whole door assembly and took out the screws that hold the plastic retaining ring for the glass door. Replaced glass and reassembled the door. Very easy repair. Took about 15 min.
Water was sprating all over the inside of wash machine onto the circuit board.
I took the two screws off the back that holds the top down, lifted it , then pulled it back to remove. After this was removed, there were two more screws holding down the assy-s housing and drawer. First remove drawer where you add the soap and softners. Then I pulled that back and the assy-s housing drawer just snaps onto the housing. I pulled the drawer off, then I took the four hoses that are connected to the back and put on the new one in their respected spot. I snapped it back on and reassembled. You don't need a maytag repair man to do this job.
(1) Remove all screws keeping them organized as a set,(some are larger than others,for the glass frame only. After all screws are removed remove frame from the door.(2) Remove old glass and replace with the new one and put it all ack together.
Watched the video, procedure was simple and as depicted on the video. Started by using a wet shop Vac to the discharge hose and sucked as much dirty wash water out as possible. Removed the pump,and found the motor did not turn freely. Removed the motor (3 screws) and replaced the motor with new part. Reassembled the washer, everything worked as it should. After about 3-4 loads of laundry, the "Not Draining" code / problem returned. Again, sucked out the water with the Shop Vac. Checked the Filter /Cleanout and found it completely packed with MUD. Cleaned that out, and again disassembled the washer. The pump was removed and the remaining muddy gunk was cleaned from the impeller. The 3 drain lines that attached to the pump were inspected for blockage/obstruction and flushed of any muddy residue. Reassembly was quick and easy, and the washer has worked well since. I have no idea how the dirt got into the system with enough dirt to gunk up the system. Recommend keeping more frequent inspections of the cleanout trap.
Take pics every step, easier re-assembly. Dismantled washer keeping bolt/screw section removed compartmentalized in a tackle box in the order of removal. Replaced drum support, bearings, seal, old blots. Too much to write but I was able to do it all in about 4 hours once all the parts finally came in.
First unplug or turn off thee circuit breaker. Then remove the two screws to the top cover. Slide the cover back about three inches then remove the cover. Next take out the screw to the old sensor. Then unplug the electrical connection by squeezing and the pulling to disengage. Now set the old unit aside. You then grad your eight inch wire tie and hold the with flat side to the right and just to the right of the screw hole for the bracket is a square hole. Feed to wire tie into the square hole with your left hand then loop down left side of the end of new sensor and back up threw the square hole and tighten with the pliers. Your new sensor will be positioned just like it was mounted to the metal bracket. And pretty ridged. Now connect the vacuum hose and electrical connector.
The part did not fit this model. The flap part fit the hole but the seal ring is too big. I cut 1\4inch out and used super glue the make it small enough to fit and seal the hose. Make sure you only use a drop of glue and keep the seal even and flat so it will seal
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
The Glass on the door cracked into a bunch of pieces.
I went to Maytag.com and typed in my model number and it came up with different parts I found the glass part I needed and ordered it. I received it in like 3 days. I had a phyllips screw driver and it the removal of the base around the glass replace the glass and screwed it right back on and started washing clothes. No leaks at all. I am a woman and proved woman can do the same things a man can do but quicker.LOL
