Models
>
WF210ANW
WF210ANW ((XAA-01)) Samsung Washer - Overview
Sections of the WF210ANW
[Viewing 7 of 7]
Keep searches simple, eg. "belt" or "pump".
Drain Pump Assembly - 120V 60Hz
PartSelect #: PS4204638
Manufacturer #: DC31-00054A
This is a 120 volt, 60 hertz drain pump assembly for a washing machine. It is a genuine OEM part. This pump helps expel water from the washing machine, and is activated after the spin speed is maintai...
$181.80
In Stock
Affresh Washing Machine Cleaner - 3 pack
PartSelect #: PS1960673
Manufacturer #: W10135699
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
$12.60
In Stock
Outer Seal Clamp
PartSelect #: PS4218211
Manufacturer #: DC97-04973B
This is an outer seal clamp for the washer door boot of your Samsung washing machine. This clamp tightly seals the boot of the drum within the door of the washer to prevent leaks. This clamp is made o...
$17.35
In Stock
VALVE-WATER;V-0117,NYLON
PartSelect #: PS4209100
Manufacturer #: DC62-30314K
One solenoid valve for hot water
$89.85
In Stock
DOOR-DIAPHRAGM;WF338AAG/
PartSelect #: PS4210921
Manufacturer #: DC64-00802B
This is a door diaphragm, also commonly known as a door boot seal, for a washer. The boot is fitted between the washer door and the tub to prevent leaking while the appliance is in use. It is made of ...
$180.67
In Stock
ASSY FIXER TUB;WV9900M,WV26R9980KV
PartSelect #: PS16224595
Manufacturer #: DC97-14489R
Shipping bolts are installed through the back of the washing machine, and hold the wash tub and basket in place while your washer is being transported. The tub suspension holds the tub correctly in pl...
$65.12
In Stock
Washer Bolt Assembly
PartSelect #: PS4217876
Manufacturer #: DC97-02412A
Assembly BOLT;SWF-P12,MOTOR/
$13.62
In Stock
Washer Water-Level Pressure Switch
PartSelect #: PS4217080
Manufacturer #: DC96-01703B
The pressure switch senses and controls the water level in the washer.
$93.87
In Stock
Questions And Answers for WF210ANW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WF210ANW
[Viewing 2 of 2]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Code indicating washer was NOT discharging water
Watched the video, procedure was simple and as depicted on the video. Started by using a wet shop Vac to the discharge hose and sucked as much dirty wash water out as possible. Removed the pump,and found the motor did not turn freely. Removed the motor (3 screws) and replaced the motor with new part. Reassembled the washer, everything wor
... Read more
ked as it should. After about 3-4 loads of laundry, the "Not Draining" code / problem returned. Again, sucked out the water with the Shop Vac. Checked the Filter /Cleanout and found it completely packed with MUD. Cleaned that out, and again disassembled the washer. The pump was removed and the remaining muddy gunk was cleaned from the impeller. The 3 drain lines that attached to the pump were inspected for blockage/obstruction and flushed of any muddy residue. Reassembly was quick and easy, and the washer has worked well since. I have no idea how the dirt got into the system with enough dirt to gunk up the system. Recommend keeping more frequent inspections of the cleanout trap.
Read less
Parts Used:
-
SCOTT from VERNAL, UT
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
7 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The water level was lower than normal.
First unplug or turn off thee circuit breaker. Then remove the two screws to the top cover. Slide the cover back about three inches then remove the cover. Next take out the screw to the old sensor. Then unplug the electrical connection by squeezing and the pulling to disengage. Now set the old unit aside. You then grad your eight inch wi
... Read more
re tie and hold the with flat side to the right and just to the right of the screw hole for the bracket is a square hole. Feed to wire tie into the square hole with your left hand then loop down left side of the end of new sensor and back up threw the square hole and tighten with the pliers. Your new sensor will be positioned just like it was mounted to the metal bracket. And pretty ridged. Now connect the vacuum hose and electrical connector.
Read less
Parts Used:
-
Fredric from ROCKMART, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!