Parts That Fix Whirlpool Dishwasher WDT970SAHV0 Not cleaning dishes properly

This authentic Dishwasher Upper Rack Adjuster Kit with white wheels is a kit made up of primarily plastic and metal components, which will require a screwdriver to install. This kit comes with all the necessary parts for a dishwasher rack adjuster. It fits onto the dishwasher rack and connects it to the track allowing it to slide in and out. If broken then the rack will no longer slide properly, and the part must be replaced. In many cases, our customers have reported the top rack of their dishwasher hanging down or sagging due to the adjuster kit, particularly if the wheels, have broken or failed. If you are having problems in this area, this kit will help get your dishwasher back up and running. Check your model number and user manual to see if this part is right for you. The parts for this kit come as a package and are not generally sold individually.

Also know as a diverter valve. This diverter motor is for dishwashers. Diverter motor controls the flow of water to the spray arms. Unplug the dishwasher and shut off the water supply before installing this part. Wear work gloves to protect your hands.

The upper spray arm rotates and sprays water to clean the dishes inside the dishwasher tub. If your dishes are not being cleaned properly, you should check if there is an issue with the spray arm. To check your spray arm, make sure the spray arms can move evenly and freely on their bearing rings and mounting brackets. Remove your spray arm and check to ensure they are straight and undamaged. This spray arm is made of high-quality plastic and is just over 5 inches long.

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

Sold individually.

The pump motor delivers water to the spray arms to clean the dishes during the wash cycle.

The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack stop may need to be replaced. The replacement part may differ slightly from the broken part, depending on the model. However, the different styles are interchangeable. This product is sold individually and comes in both a white and grey plastic version. Many of our customers found this repair to be very easy and takes less than 30 minutes to complete. Simply snap the old part out and snap the new part into place. You will not require any tools to complete the job. This is an authentic part approved by the manufacturer.

Detergent dispenser W10861000 is an original equipment manufacturer (OEM) part that fits some Whirlpool, KitchenAid, Maytag and Amana dishwashers. Detergent dispenser W10861000 attaches to the inner door panel and holds the dishwasher detergent and rinse aid in covered compartments. This dishwasher detergent dispenser measures approximately 5 inches wide and 4.5 inches high.

This pump and motor assembly are for dishwashers. Pump and motor assembly pumps water through the spray arms during the dishwashing cycle. Shut off the house circuit breaker for the dishwasher before installing this part. Wear work gloves to protect your hands.

The tine pivot clip, also known as the tine row pivot, is used in dishwashers and is located in the upper dishrack. At around 3 inches in length, the clip is used to keep the tine row in place in the dishrack. If your clip is cracked or damaged, it is best to replace this part. To repair, first lift the release tab and hold the other side to prevent it from falling off. After lifting it off, you can set the new clip on the tine row and lock it up. Refer to the manual provided by the manufacturer for further installation instructions and guidance. Remember to wear work gloves as a safety precaution. This repair was rated as very easy by our customers and should be done in 15 minutes or less.

This drain hose is 6 and 1/2 feet.

Also known as rack adjuster. Sold individually. This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip holds the adjuster arm in the right position on the dishrack. The most common reason for replacing the strap is if the rack will not stay in its desired position. This part is sold individually. There are no tools needed to replace the positioner.

This part is used to drain water from your dishwasher.