Models
>
SHPM78Z55N
SHPM78Z55N (01) Bosch Dishwasher - Overview
Sections of the SHPM78Z55N
[Viewing 9 of 9]Keep searches simple, eg. "belt" or "pump".
Adjustable Tine Row Clip
PartSelect #: PS8727471
Manufacturer #: 00611981
This part is a replacement tine row clip for your dishwasher. The tine row clip is adjustable, and it fits onto your dishrack to holds the tines into place. If your dishrack tine rows will not stay in...
$5.86
In Stock
Door Seal
PartSelect #: PS8723143
Manufacturer #: 00494772
This seal is also referred to as a door gasket, and it is designed for use on dishwashers. It is installed on the door of the appliance, and it seals the space between the tub of the dishwasher and th...
$31.10
In Stock
Dishwasher Circulation Pump with Heater
PartSelect #: PS11724988
Manufacturer #: 12008381
This circulation pump with heater is for dishwashers.
Circulation pump with heater moves heated water through the spray arm to clean the dishes.
Unplug the dishwasher before installing this part...
$145.95
In Stock
Questions And Answers for SHPM78Z55N
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jane
May 11, 2023
How do you drain the dishwasher without running a cycle?
For model number SHPM78Z55N
Hi Jane, thank you for reaching out. To drain the dishwasher manually, put the drain hose in a bucket and set your dishwasher to drain by pressing the drain/cancel/start button for three seconds. Then close the dishwasher door to start it. While the drain tube is in the bucket, shake it to loosen the obstruction. When water comes shooting out, let it continue until it’s fully drained. If the bucket fills up, open the dishwasher door to stop the drain. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Bob
23 days ago
WHAT IS A ZEOLITE FILL TUBE
For model number SHPM78Z55N
Hi Bob, thank you for your question! Zeolite container assembly, part number PS12718976, aids in the spot-free drying of the dishes. We hope this information helps!
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
Common Symptoms of the SHPM78Z55N
[Viewing 10 of 10]Leaking
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Not drying dishes properly
Fixed by
these parts
these parts
Show All
Will not dispense detergent
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
E:15 error code with Watertap
The E:15 error code means water is detected in the pan under the unit. There are several ways this can happen.
In this case, it was caused by a bad inlet valve. It did not close properly and led to an overflow of water inside that eventually spilled into the pan underneath the unit.
I see now why the pump keeps run ... Read more ning after this error. In this case, it would have led to a big flood in the kitchen if it did not.
I was actually able to run the unit while broke by manually operating the valve under our sink that provides water to the unit.
Be sure to turn off breaker before servicing. Don't get shocked!
Be sure to turn off water before starting! Or, you'll have a flood.
Anyway, I just pulled the unit out (was secured by 2 screws on the sides). I lifted up the insulation material on the left side to get at the valve. Pushed a little green tab to release the electrical plug. Then, use pliers to move clamp off the white water hose on the inside. Then, pull of white hose. This was hard in my case. Took a lot of force. Then, reach behind the unit and use pliers to unscrew water hose. Now, the whole gray panel there can pop out with some force. Then, slip the old valve out and slip new one in. Reconnect hoses and clamp. Note that I put some caulk on the connector where white hose goes. Not sure if needed or not.
Good luck!
In this case, it was caused by a bad inlet valve. It did not close properly and led to an overflow of water inside that eventually spilled into the pan underneath the unit.
I see now why the pump keeps run ... Read more ning after this error. In this case, it would have led to a big flood in the kitchen if it did not.
I was actually able to run the unit while broke by manually operating the valve under our sink that provides water to the unit.
Be sure to turn off breaker before servicing. Don't get shocked!
Be sure to turn off water before starting! Or, you'll have a flood.
Anyway, I just pulled the unit out (was secured by 2 screws on the sides). I lifted up the insulation material on the left side to get at the valve. Pushed a little green tab to release the electrical plug. Then, use pliers to move clamp off the white water hose on the inside. Then, pull of white hose. This was hard in my case. Took a lot of force. Then, reach behind the unit and use pliers to unscrew water hose. Now, the whole gray panel there can pop out with some force. Then, slip the old valve out and slip new one in. Reconnect hoses and clamp. Note that I put some caulk on the connector where white hose goes. Not sure if needed or not.
Good luck!
Read less
Parts Used:
-
Raymond from VIENNA, VA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers
25 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing the pocket handle on a Bosch Dishwasher
I removed the 3 #20 torn screws in the handle, and the six #20 tore screws inside the door that hold the outer door skin in place.
The plastic handle has a series of molded hooks that allow it to snap into the stainless steel skin.
To avoid damaging the skin, use a utility knife to cut behind the two large hooks o ... Read more n the bottom of the handle and the one on each end. One trimmed, the handle easily slides out of the door skin.
The new one will effortlessly snap in-place, then reposition the door skin and fasten with the 9 screw previously removed.
The plastic handle has a series of molded hooks that allow it to snap into the stainless steel skin.
To avoid damaging the skin, use a utility knife to cut behind the two large hooks o ... Read more n the bottom of the handle and the one on each end. One trimmed, the handle easily slides out of the door skin.
The new one will effortlessly snap in-place, then reposition the door skin and fasten with the 9 screw previously removed.
Read less
Parts Used:
-
Michael from CASTLE ROCK, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
14 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The middle rack was rusting and some of the pegs were coming off.
Removed the spray arm, front handle, and little clips from the old rack and installed onto the new rack. Was very simple.
Parts Used:
-
Susan from MIDDLEBURY, VT
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
11 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!