This is a replacement dishrack roller or wheel for your dishwasher. It is made of gray plastic, measures a little over an inch in diameter, and is sold individually. This roller is designed for the lo...
$11.12
In Stock
Order within the next 6 hrs and your part ships today!
This seal is also referred to as a door gasket, and it is designed for use on dishwashers. It is installed on the door of the appliance, and it seals the space between the tub of the dishwasher and th...
$31.10
In Stock
Order within the next 6 hrs and your part ships today!
This circulation pump with heater is for dishwashers.
Circulation pump with heater moves heated water through the spray arm to clean the dishes.
Unplug the dishwasher before installing this part...
$145.95
In Stock
Order within the next 6 hrs and your part ships today!
Order within the next 6 hrs and your part ships today!
Questions And Answers for SHEM78W55N
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sunil
December 26, 2019
When i open the dishwasher door the whole front panel and the console comes out.
For model number SHEM78W55N
Hi Sunil, thank you for your question. You may want to take a look at your door panel and the screws that hold your door together to make sure everything is secured. Good luck with your repair.
Was this helpful?
Thank you for voting!
Kurt
August 21, 2023
So I have replaced the discharge pump after receiving an Error 24 code. I did this after checking all aspects of the drain system to ensure I had no blockage. The dishwasher functions fine with proper discharge into the garbage disposal. That is right up until the last 30 minutes where I get the error code 24 with water tap indicated. Not sure what my next steps are because nothing goes beyond the discharge pump.
For model number SHEM78W55N
Hello Kurt, thank you for contacting us. Based on our research, the error code 24 indicates that the dishwasher is not draining properly due to the drain filter being blocked. Since you have replaced the discharge pump and that does not solve the problem, we would suggest replacing the fine filter, part number PS8737146, to resolve the issue. It removes food particles and debris from the water to prevent the drain from clogging. We hope this helps!
The E:15 error code means water is detected in the pan under the unit. There are several ways this can happen.
In this case, it was caused by a bad inlet valve. It did not close properly and led to an overflow of water inside that eventually spilled into the pan underneath the unit.
I see now why the pump keeps run
... Read morening after this error. In this case, it would have led to a big flood in the kitchen if it did not.
I was actually able to run the unit while broke by manually operating the valve under our sink that provides water to the unit.
Be sure to turn off breaker before servicing. Don't get shocked!
Be sure to turn off water before starting! Or, you'll have a flood.
Anyway, I just pulled the unit out (was secured by 2 screws on the sides). I lifted up the insulation material on the left side to get at the valve. Pushed a little green tab to release the electrical plug. Then, use pliers to move clamp off the white water hose on the inside. Then, pull of white hose. This was hard in my case. Took a lot of force. Then, reach behind the unit and use pliers to unscrew water hose. Now, the whole gray panel there can pop out with some force. Then, slip the old valve out and slip new one in. Reconnect hoses and clamp. Note that I put some caulk on the connector where white hose goes. Not sure if needed or not.