SGR351CQ0 Westinghouse Dryer Parts & Repair Help | PartSelect
Models > SGR351CQ0

SGR351CQ0 Westinghouse Dryer - Overview

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
(90)
PartSelect #:PS459829
Manufacturer #:5303281153
This rear drum bearing kit is designed for use with dryers. It supports the rear of the drum in your appliance as it tumbles your clothes during the drying cycle. If your drum will...
$29.44
In Stock
(45)
PartSelect #:PS1148434
Manufacturer #:134503600
This drum belt, often referred to as a drive belt, is used in the assembly of dryers. It goes around the drum, the idler pulley, and the motor pulley. As the armature on the motor ...
$13.43
In Stock
(18)
PartSelect #:PS418807
Manufacturer #:131825900
If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear b...
$4.33
In Stock
(15)
PartSelect #:PS5574052
Manufacturer #:137513300
This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there a...
$37.96
In Stock
(10)
PartSelect #:PS975832
Manufacturer #:134398300
This part is used to start the dryer once you have selected a setting on the timer.
$34.25
In Stock
(16)
PartSelect #:PS418433
Manufacturer #:131658800
The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, w...
$36.85
In Stock
(5)
PartSelect #:PS832645
Manufacturer #:5303937183
The lower front felt seal with adhesive, also known as a drum felt seal, is used in dyers and allows the drum to easily glide on the front panel. For this repair project, you will ...
$22.27
In Stock
(22)
PartSelect #:PS470049
Manufacturer #:5303931775
This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes...
$29.76
In Stock
(2)
PartSelect #:PS12579101
Manufacturer #:131724301
This drum bearing bracket is for dryers. Drum bearing bracket holds and supports the drum bearing
$8.20
In Stock
(1)
PartSelect #:PS418736
Manufacturer #:131777700
This ball hitch provides support to the drum located at the back wall of the dryer. This allows the drum to spin. The bearing may have gone bad and you might notice that the ball i...
$57.53
On Order
Questions and Answers for SGR351CQ0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Loud Squeaking

Rear Drum Bearing Kit – Part Number: 5303281153
  • Customer: Frank from Boyertown, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 307 of 316 people found this instruction helpful
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Acc... read more

Motor would hum but not turn on when start knob was turned.

  • Customer: Elvis from Miami, FL
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 212 of 245 people found this instruction helpful
The motor bearings had stiffened up – classic planned obsolescence.

I could tell the motor was bad, because when I tried to spin the drum by hand, it wouldn't turn in any direction. (Normally it can turn fairly easily.)

(Helpful hint: As you remove screws / parts, place them in a plastic baggie, and write on the baggie from whence t... read more

squeeking like crazy

  • Customer: Steve from Wheelersburg, OH
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 119 of 135 people found this instruction helpful
well, i started at the top and worked my way down. by taking the top off, it gave me more room to get the dryer tub out. took the two screw`s out of the vented plate on the back of the machine to undo the belt. this is a stackable washer-dryer combo, so next i took off the white plate on front between washer & dryer. took off the control panel, unpluged it, ... read more