Your Subscriptions
Models
>
RST307
RST307 (ALL/RST307/ALL) Maytag - Overview
Sections of the RST307
[Viewing 7 of 7]
Keep searches simple, eg. "belt" or "pump".
2 Piece Broiler Pan
PartSelect #: PS971245
Manufacturer #: 4396923
This is cookware designed for use in your range or oven. It is a two-piece dish that is used to grill or cook food while the broil function is on, meaning it can withstand high temperatures. This set ...
$37.27
In Stock
Wire Oven Rack
PartSelect #: PS11740769
Manufacturer #: WP314763J
This wire oven rack is used on some ovens and ranges. It is twenty-three inches long and it is made of metal.
$40.86
In Stock
Anti-Tip Bracket
PartSelect #: PS11741944
Manufacturer #: WP3801F656-51
Sold individually.
$5.66
In Stock
Hinge Kit - Right Side
PartSelect #: PS2172201
Manufacturer #: R0706011
The hinge kit, or oven door hinge, is used in ranges and wall ovens. The hinge attaches to the right side of the door and controls how fast the door opens. At a specific angle, it allows the door to r...
No Longer Available
Gas Burner Cap with Spark Electrode
PartSelect #: PS11757448
Manufacturer #: WPY0307210
This stainless steel surface burner cap assembly comes with a spark ignition electrode, and is used for some Maytag/Amana brand gas ranges and cooktops. Available only in the chrome finish you see here.
$31.03
In Stock
Surface Burners Spark Module Kit
PartSelect #: PS2011188
Manufacturer #: 1430322
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
No Longer Available
Top Burner Knob
PartSelect #: PS2191641
Manufacturer #: Y0300705
Sold Individually. This knob accepts a D-shaped shaft.
No Longer Available
Gas Valve
PartSelect #: PS2191632
Manufacturer #: Y0300664
This part makes sure that no gas is released until the igniter gets enough power to ignite the gas range.
No Longer Available
Gas Spark Ignition Switch
PartSelect #: PS11757445
Manufacturer #: WPY0300521
This burner ignition switch is a little over an inch long. It is made of plastic and has a white center cam. This switch has some metallic components.
No Longer Available
Questions And Answers for RST307
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the RST307
[Viewing 3 of 3]Door won’t close
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Purchased home but stove had no broiler pan.
-
Raymond from BLOOMINGTON, MN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
14 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
gas burners and gas oven would not light
unplug the oven and pull it away from the wall. looking at the oven from the back, the spark module is at the bottom on the lower left. there is a two piece sheetmetal cover over the area of the spark module. use a phillips head screwdriver to remove five screws and the covers come off. the spark module is the blue cube with four push on wire connectors. all you have to do is hold the new one next to the old one and swap one wire at a time. both were clearly marked with identical numbers and letters. really nothing to it. it took me longer to clean the back of the oven than to replace the module. the old module was eaton part number Y-54052-3. the new one is eaton part number Y-054052-34.
Parts Used:
-
nicholas from livermore, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
14 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rivet broke on the right side oven door hinge
Regarding my right side oven door hinge replacement, P/N PS2172201
After reading that other people had trouble threading the screws into the new hinge, I looked at the drilled mounting holes in the new hinge. Neither hole was threaded. The smaller hole used a self tapping sheet metal screw which works fine. The larger hole gets a machine screw and will not self tap. Since the instructions say put the screw in "once" to tap the holes before installing the hinge, I tried this. It doesn't work, regardless of what the instructions say. The larger hole should come from the manufacture threaded. I do have a tap and die set so I tapped the hole myself. After that, the installation is a 5 min. ordeal.
Take the two screws, one on each side, out that hold the oven door on the hinges. The door will then pull straight off the hinges. Take the storage drawer below the oven out. Unscrew the top and bottom hinge screws and pull the old hinge out from inside at the bottom. Put the new "threaded" hinge into position and hold from the bottom, inside. Screw in the two screws, large one on the top end, and put the door back on. You can open both hinges about 30 degrees to allow the door to slide back on the hinges easily. Put the last two screws in that hold the door to the hinges and you are done.
Really very easy and saved several hundred dollars in repair bills. I might add that my hinge arrived on time 3 or 4 days after the order was placed.
After reading that other people had trouble threading the screws into the new hinge, I looked at the drilled mounting holes in the new hinge. Neither hole was threaded. The smaller hole used a self tapping sheet metal screw which works fine. The larger hole gets a machine screw and will not self tap. Since the instructions say put the screw in "once" to tap the holes before installing the hinge, I tried this. It doesn't work, regardless of what the instructions say. The larger hole should come from the manufacture threaded. I do have a tap and die set so I tapped the hole myself. After that, the installation is a 5 min. ordeal.
Take the two screws, one on each side, out that hold the oven door on the hinges. The door will then pull straight off the hinges. Take the storage drawer below the oven out. Unscrew the top and bottom hinge screws and pull the old hinge out from inside at the bottom. Put the new "threaded" hinge into position and hold from the bottom, inside. Screw in the two screws, large one on the top end, and put the door back on. You can open both hinges about 30 degrees to allow the door to slide back on the hinges easily. Put the last two screws in that hold the door to the hinges and you are done.
Really very easy and saved several hundred dollars in repair bills. I might add that my hinge arrived on time 3 or 4 days after the order was placed.
Parts Used:
-
Roger from Pleasanton, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
7 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
