RS10 - Instructions

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

removed screws holding element and detached wires and simply removed it; no problem. Reversed the process to install the new one. The great thing is that I ordered this element one morning and received it the very next day! I have saved this website for future problem solutions because I know they are well organized and dependable. Thanks for saving our week!!

First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With the help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.

just diconnected the electric unscrewed the 2 screws that held the element in place, then i unplugged the old element, plugged in the new element, replaced the 2 retaining screws. that was it! Frigidaire customer service had no clue how to help me find this element for an old wall mount oven. I spent over a half hour on the phone with them.
The cool part about parts select is, I was on the phone with them less than 5 minutes and had already found and paid for the element i was looking for. on and off the phone in less than 5 minutes.
Thanks a lot parts select, what a great experience doing business with you.

Very easy to replace old bake element with new one. Used screw driver to remove the old element, disconnected wires then connected wires to new element and used the screw driver to secure new element.

After removing the 2 screws, pulling the element out, & disconnecting the 2 wires, I started installing the new element. 20 years ago, this may have been easy, but...after so many years of use, and grease fumes and who knows what, the new connections were difficult to connect. However , after a few choice words and a few alcoholic beverages, the new burner was installed and it works great! Thank you & keep stocking those "old" parts. I have 3 more burners & an oven fixture left ta go!

Older model Frigidaire oven (1957?). Worried that couldn't find the bake element for it. Called and got help. Measured the possible part from picture online and looked like it might work. Sure enough it did. Part arrived quickly and matched up well enough and installed with screwdriver in less than 30 minutes. Powered it up and it "glowed" with delight. My wife had her oven back!

Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise

Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.

I mistakenly thought I had to remove the microwave to get to the back, not so. I would have had access to what I needed to unscrew; but I have to admit the hassle of taking it down and putting it back equals having to work on it attached to the shelf-your call on how you do this. I unscrewed the front top to remove the vent piece that is across the top front of the microwave. This will reveal the control panel screw. (While you have the vent removed you might want to clean the vent and the exposed filter.) carefully lift and pull out control panel. I unplugged a piece as the wires were tied tight. It will not completely detach, so carefully tip it back from exposed insides. The fuse is not clear but white with silver ends so look in upper right for it. I popped it out and replaced it. Replugged the wired part to cover and carefully fit tabs in and slide down to secre. Replace screw, replace vent piece and secure screws on top of microwave. I plugged it in to test before putting it back above my stove.

I didn't. Don't know how to get to light bulb to change it for this specific model

This is a big old probably 1950's 40"+ wide electric range with a left and right oven four top burners and a large prep area....the left oven lower bake element failed.....do not try to remove the element....simply slide out oven chamber after removing the safety bracket at the top that keeps the chamber from falling out....probably designed like this for easy cleaning.......the bake element is bolted to the back wall bracket so there are nuts on the back side to remove along with and a contact ground strap......the replacement element has bayonet type connecteors while the original had bent flat metal contacts......I was able to adjust the tension on the stationery contacts in the oven so the beyonet made a good connection....no clue how to duplicate the contacts on the original element nor did I see a choice in my on line parts search......fingers crossed this will last.....great old electric range with spacious ovens

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Remove old tray, clean old caulk, and clean inside of microwave, Place new tray-glass floor and caulk with heat resistant silicone. Easy project.