Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
50+ Yr Old Cooktop Burner had one of its two coils burn out
The hardest thing was finding the part to order! The GE Cooktop is from 1957 when the house was built. I followed the instructions that came with it. After seeing where the screw on hinge was supposed to be, I cleaned away the caked grease and finally saw the screw. I had to use a nut driver to remove it since it didn't have a slot for a screwdriver. Once that screw was out, the rest was easy. Before disconnecting any wires, I laid the new and old parts beside each other and drew a diagram showing where each wire (red, black & white) connected. It was a bit scary stripping the wires since they were old and fragile. It said to bend them into a "U" and solder but I didn't have soldering skill or equipment so I just tightened the screws holding the wires carefully. The connections are all nicely isolated in the bakelite insulator so it didn't seem cruicial. After working the new unit into place and turning on the power (at the circuit breaker), the burner worked perfectly. The replacement part looked exactly like the original. I was so amazed to be able to obtain the replacement burner after all these years! Thank-you PartsSelect!
It was so easy. I turned off the power to the range, loosened the hinge screw and removed the burner unit from the stovetop. Next I removed the two spring clips holding the ceramic housing covering the three connectors. Then I loosened the three screws holding the 3 wire connectors to the burner, reconnected the 3 wires to the new burner unit, positioned the ceramic insulator housing and reinstalled the spring clips and finally replaced and tightened the hinge screw. It took about 5 or six minutes, max. You can do this!
The lower bake element in the upper oven burnt out.
In order to determine what was wrong with the oven I used a voltage meter to determine if power was coming to the element in the first place. Be careful to set your meter at least 500 ACV, as the oven is operating at 240V. Remove the two screws that hold the element in place and carefully pull it out of the side of the oven. Turn on the bake element in the upper oven and place your test leads to either side of the connection leads. If you get a reading of 240Volts plus or minus you will know for sure the element is bad. Turn off the oven, or even better turn off the circuit breaker to your stove. There are two leads to the element that are held in place by self taping screws. If you have the same luck I have they will be corroded together. Carefully use long nose pliers to hold steady while gently applying pressure. If necessary use liquid wrench. When separated put together in the reverse order as how you took it apart.
Both 8" surface units not working on 30+ yr. old range top
Raise burner high enough to remove screw located on hinge between coils. Remove screw completely and lift-out burner and ceramic block with wire connections. Remove the wires from the connector block and strip-back the ends of both about 3/4". Make connections per the diagram and then assemble the ceramic blocks around the connection in a sandwiched fashion and secure the halves with the clips provided. Now sit the burner down into place. An extra pair of hands is good here to hold the chrome trim ring and the coil up directly opposite the hinge. Then, peek under the coil and using fingertips, get the screw provided started in the hinge bracket and run this screw up snugly. A 1/4" nut driver makes this part easier, but a screwdriver will get it done. That's it. Just flip the breaker to restore power and cross your fingers. A fairly easy job that took about 40 minutes to do both 8" elements The potentially frustrating parts are the ceramic terminal block assembly and replacing the hinge screw, but a job that's very doable. Oh, don't forget to slip the drip pans back in.
Find, Order, Receive & Replace electric stove burners
Teh instillation was a simple matter of removing the old burners and replacing them with the new ones. Removal required the screw connector on each burner ring to be loosened and the reverse done when the new one was installed. The hardest part was finding the correct burners since the Model number of the stove was not in anyones file. This web site provided adequate pictures of the part to permit identification of the likely part to order. Thanks.
The bake elment was over 25 years old when it cracked and burned out.
Turned off the electricity to the ovens. Unscrewed the two screws holding the old bake element. Removed the old one by disconnecting the two wires and replaced the new element in it's place.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the four wires The element i request was 3 elements and i received two element but it was very easy i connect only the 3 wires.
Original cooking element was starting to fail. It was bending and changing form and would have broken over a short period of time.
I had purchased a partselect heating element for my larger lower oven previously so I knew what to expect on replacement.
I shut off the power to the stove from the electrical box. Next I removed both the cooking racks from the oven. Then the side removable panels and bottom as this is a P7 removeable panel oven. This gave ne easy access to the nuts/screws holding the element in place. Once the screws were removed I pulled out the element and disconnected the leads. I replaced the new piece reversing the process.
Finding a replacement element for a 30 year old GE electric stove was difficult to find. I was overjoyed when I found a replacement on Partselect! It was a simple "Unscrew, reattach wires and install" all in about 10 - 15 minutes all with a nutdriver. Plug in elements are common but to find one with screw connections is not easy, THANK YOU PARTSELECT! A $48.00 investment (Element with trim ring) was worth the cost compared to a $1,400.00 replacement. You just made a loyal customer, again, Thank You.
First I removed the screw that holds the element in place. I then pulled the element out about 3 inches and disconnected the three wires. Then I just had to do it in reverse. EASY!
Wire connection from the oven was too small and I had to make it larger with a flat head screwdriver and pliers. I used a head flashlight for I could see better. I would suggest not having a glass of wine before starting the repair. It would have only taken me 15 Minutes instead of 30.
