Models
>
RF26VACWP
RF26VACWP ((XAA-00)) Samsung Refrigerator - Overview
Sections of the RF26VACWP
[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
Door Mullion Spring
PartSelect #: PS4163672
Manufacturer #: DA81-01345B
The French door divider spring fits most Samsung French door style refrigerators. The spring applies tension between components in the refrigerator, which engages and retracts the door flap. This will...
$13.24
In Stock
Spring PIN - French
PartSelect #: PS4163673
Manufacturer #: DA81-01346A
This pin acts as a sleeve for the French door spring in a refrigerator. This is a genuine OEM part that is sold individually and works with the spring within the door mullion to seal the door shut. If...
$4.18
In Stock
Evaporator Fan Motor
PartSelect #: PS4138376
Manufacturer #: DA31-00146E
This evaporator fan motor is in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated. When the evaporator ...
$137.25
In Stock
Gasket - Right Or Left Side
PartSelect #: PS4151582
Manufacturer #: DA63-06542A
Sold individually.
$156.90
In Stock
Refrigerator Evaporator Fan Motor
PartSelect #: PS4138377
Manufacturer #: DA31-00146H
This evaporator fan motor is sourced from the original manufacturer for use in refrigerators. It circulates cold air throughout the refrigerator compartment to maintain consistent cooling. If the evap...
$136.42
In Stock
Questions And Answers for RF26VACWP
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the RF26VACWP
[Viewing 2 of 2]Door won’t open or close
Fixed by
these parts
these parts
Show All
Fridge too warm
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Left side French Door flap on Samsung refrigerator didn't retract when closing.
OMG seriously! I stopped into my go-to appliance repair shop to ask about what might be needed to repair the problem with my refrigerator door. They said you will need to replace the Mullion Flap piece. Cost would be $250-300 with part, labor and service. I went on line to see if I could handle the repair process myself. I found a How to
... Read more
- U Tube video and turns out I only needed to replace a little spring and pin not the whole Mullion Flap. Went to Parts select, ordered the spring and pin and did the repair myself in about 5 minutes. Shipping was $7 so I ended up paying $13 total.
Read less
Parts Used:
-
HOLLIE from FORT WAYNE, IN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
41 of 51 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Installation Video Incorrect
The installation video notes that the door mullion spring has a bent end, and that the bent end of the spring is to be inserted into the LOWER hinge. However, on my refrigerator door, the bent end of the door mullion spring must be inserted into the UPPER hinge in order for the door to function properly. (Also noted that in your video t
... Read more
he installer manually closed the door mullion rather than just closing the refrigerator door, another indication that the installation of the spring was incorrect.) After watching the video several times to confirm I was installing the door mullion spring according to the video instructions, I tried inserting the bent end of the door mullion spring into the upper hinge, which proved to be the correct installation of the door mull spring. What should have been a 5 minute repair turned into an ½ hour repair.
Read less
Parts Used:
-
Cheryl from PALATINE, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers
18 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
spring in door mullion had broken
There is a pretty good video about this on youtube, but complications arose nonetheless. The replacement spring supplied by Partselect is a bit different from the original in two ways. First, it is made of heavier-gauge wire; this is a good thing for durability, but it makes installation tougher. Second, the ends of the spring, which a
... Read more
re bent at right angles to the spring axis in order to fit into the plastic sleeves that hold the spring ends, are far too long. Once I figured this out, i snipped the ends down by a quarter inch or so, and they fit into the sleeves just fine after a certain amount of persuasion from needle-nose pliers. All things considered, it was a bit harder than it should have been, but the door works now, so all is well.
Read less
Parts Used:
-
Gary from TUPPER LAKE, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers
10 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!