Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
electric ignite gas stove kept clicking the ignitor unless unplugged from electrical outlet
I removed the 2 screws that held the housing on at the back of the stove. Then I removed the 2 screws that held the module to the back of the stove. Since I am not an experienced electrical person (I am a female nurse in the operating room), I unplugged 1 wire at a time from the old module and plugged it into the new module. I repeated this step with each wire to make sure I didn't put the wrong wire on a wrong spot until I had all the wires to the new module. Then reattached the screws, plugged in the oven and presto, it works just fine! Was amazed at how easy it was. A 50 dollar part instead of a new 1500 dollar stove. How easy is that?
Had to remove the 4 range knobs, and the oven knob and then the facie. Two screws under the end caps and two on each side from the back on each end. Design defect: one of these screws which attaches through the frame to the facie also attaches the support which holds up the range top. Take that one off last. Remove the two wires that attach to the oven light switch. After detaching the power supply to the defective ignition unit, it just pulls right off. Push the new switch on over the knob shaft and reassemble.
Removed the defective igniter, removing one screw and disconnected wire, replaced new ignighter in reverse fashion. And WELLA! The old oven works again!!
Removed the burner plates. Lifted up the range top. Removed the knobs. Unbolted the 2 rounded nuts at top of face plate. Removed the 4 screws that hold the face plate in place from behind. Un plugged the old switch and plugged in the new one and bam! The burner worked. Thanks, Super fast shipping! The part was here in less than 36 hours. John, N.J.
I used the experience of another user posted on your web site. I removed all the gas control knobs and then I followed his instructions about removing the four phillps head screws that held the front plate in place. Once I had it loose and flipped the plate out, it was simple to disconnect the old ignitor switch and install the new one. Simply reversing the process put the range back in proper order. Took a little over 15 minutes to accomplish.
Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time. Steve
The repair was really easy! I read a review where the gentleman had order the wrong size and that had me a little worried because I did not specify a size. There were three seals on my range so I figured if one broke I might as well replace all three. When I received the seals they were the right size and it took me less than five minutes to put them on. No tools needed because they had hooks on each end. Thanks a lot!
Used 2 side seals to make a new top seal (no longer available). Cut the 2 new side seals to provide about 1/2" less length than the old top seal. Removed one of the end hooks and straightened the hook, removed the old silicone from the hook. Used high temperature silicone and the old hook to splice the cut ends together. Let cure over-night and reinstalled. Works like a champ.
Side seals were normally deteriorated on old wall oven
I used the 14 in. Seals which are shown in their packaging as folded in a U - shape. The two tabs on either end slipped into their retainer holes easily requiring just enough stretching to flatten them. It all all took less than a minute, including opening the package. Very satisfying.
Removed broiler door springs, removed door slide arms that attach to broiler tray, two screws on each side. Removed tray and replaced slide guides. Instassed in reverse order. Works great: Thanks, Best thing about this repair was that the parts ordered were right and fit..........