Parts That Fix Hotpoint Range RB787WH1WW Element will not heat
Element will not heat is a commonly reported symptom for the RB787WH1WW Hotpoint Range, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your RB787WH1WW Hotpoint Range that will fix Element will not heat. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
The bake element is located on the bottom of the oven. If your oven will not heat properly it may be due to a faulty or damaged baking element. If you can see that the element has been separated or blistered, you should replace the part immediately. If there is no visible damage, turn the oven on and check to see if the element heats evenly. If the element is not heating evenly, or if it is not heating at all, it will need to be replaced. This element is 19 inches wide x 19 inches long, and has male spade push on terminals.
Replacing your General Electric Range Bake Element - Push On Terminals - 240V
Customer Repair Stories
Broken heating element
2)remove 2 bolts holding heating element
3)pull element out of the back of the oven about 8" so that the wire connects is visable
4)pull wire clips off of heating element and remove element from the oven
5)put wire clips on the new heating element
6)push new heating element back into the ... Read more holes in the back of the oven
7)screw botls back into the oven holding the heating element in place
8)Turn power back on
-
Paul from anna, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
Lower bake Element would not heat.
-
Ronald from Nassau, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers
This haliant burner element is a gneuine OEM replacement part for your stove. This element is 8 inches in diameter. The element lies underneath the stovetop, and will need to be replaced if it stops heating. To complete this repair you will need a 1/4 inch nut driver and a flat blade screwdriver. To access the element, open the oven door and unscrew the two screws under the lip of the cooktop.
Customer Repair Stories
Left rear element would not get hot.
-
John from Hopewell Junction, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Large burner would not get hot
-
Kevin from Leominster, MA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
This switch controls the small burner on a range/stove top.
Replacing your General Electric Range Range Surface Element Control Switch - 6 Inch - 1560 W
Customer Repair Stories
Replace stove top burners (3 total)
-
Thomas from Bonifay, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench (Adjustable)
back burner not getting hot
-
William from Shenandoah, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Customer Repair Stories
Heating element burned out.
with a 2 x 3.Unscrewed the two screws that were holding
-
LANCE from ORELAND, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Coil Burned Out
-
Frank from St Augustine, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
This broil element is found on the roof of the oven.
Replacing your General Electric Range Broil Element - 240V
Customer Repair Stories
Broiler element was burned out
-
Ursula from Suffolk, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Broiler burnt out.
-
ellen from centennial, CO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
This switch controls the large burner on a range/stove top.
Replacing your General Electric Range Surface Burner Switch - 8 Inch - 2100W
Customer Repair Stories
Top glass top burner wasn’t working
-
Robert from PAWTUCKET, RI
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Replace Surface Burner Switch
Remove rear panel of stove with a nut driver or socket. Remove knob from switch and use small screwdriver to remove screws on front panel switch. Remove and replace each wire contact one at a time to ensure correct wiring configuration. Replace screws on front panel to secure switch. Plug stove in and check that it work ... Read more s properly. Replace rear panel and move stove back in place.
-
Mark from CHANNELVIEW, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
This part provides a way of connecting individual electrical wires and offers protection of the device from electrical surges (voltages and/or currents).
Customer Repair Stories
Original terminal block plastic shielding melted, protecting appliance when the wires overheated.
-
Brian from DOVER, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
terminal block melted
-
jonathan from willow springs, IL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers