RB120PXYB0 Whirlpool Wall Oven - Instructions

Removed the broken element by taking out the two screws in the back wall of the oven and unplugging the wires. Then did reverse to install the new element. Very simple repair job.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

turned off the breaker (240 volts and it was outside, so it took longer than 15 minutes). Removed two screws in the back of the oven, one on each side of the old element, and pulled the old element forward. The wires on the back add some resistance, but they are long enough to pull forward a short distance (3 inches) without damage. Unplugged the old element, plugged in the new element, pushed it into place, and reinstalled the screws. Turned the power back on and it worked! Saved some money for the holidays! DIY para vida!

Turned off power to range because I was scared. Unscrewed broiler element, pulled part forward and pulled off wires that were attached to the back, attached wires to new element, pushed it back in place, screwed it back on to oven. Cooked my bruchette!

Turned the circuit breaker off. Removed the 2 screws holding the element in place, pulled the element out far enough to access and disconnect the wires. Installed the new element by reversing the process. Success - wife is happily baking again!

Purchased 2 piece broiler pan from this site

Shut off wall oven circuit.Took out screws, pulled element out, disconnected oven wire terminals from old element and popped them onto new element.Pushed them back behind oven wall and put screws back.Flipped circuit back on and baked some chocolate chip muffins :) Got tired of asking Hubby to fix it.You GO Ladies! ;-)

This was amazing. First I couldn't believe I could find a part for an over that was 25 years old. Fixing it was just as easy. I read some of the other reviews and it was just as easy as they described. Unscrewed the two plates on the back of the oven, unclipped two pieces and screwed the plates back on. It took me a total of 10-15 minutes, BUT, I couldn't get the door back on. Had to impose on a neighbor to help. Ten minutes to fix the oven and three days to get the door back on! Still worth it. THANK YOU THANK YOU THANK YOU

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Recieved the part within 24 hrs after I ordered it which was awesome.
Removed the two screws holding element in place and pulled out to remove old element. Disconnected the wires and removed element. Had to replace the wire ends with slip on ends to match new element. Spent more time at Home Depot looking for $.99 ends and a crimper than it did to do the entire replacement. Reinstalled element with no problem. Worked great.

First I removed the ovem door, then I removed the 4 screws, unplugged element and plugged in the new one, then replace the screws and door. It should have been a 10 min job but I'm old and a bit fat...slowed me down.

1. Move oven out from wall 2. Remove back panel of oven, 8 screws 3. Remove 3 screws inside oven holding element 4. Pulled wire connections off of element 5. Reverse procedure to install new element

I must compliment PartSelect on their quick responce and delivery of the item ordered. It arrived a day after I had ordered it. Trust me, the $40.00 I spent on the item was way cheaper than having a repair service fix it or having the entire oven replaced. I would highly recomend anyone to utilize PartSelect.

I didn't. Don't know how to get to light bulb to change it for this specific model

First I turned off the circuit breaker...just to be safe. I removed the two screws that hold the element in place. I was surprised you didn't went new screws, but that was OK. I pulled out the old one, and pulled out the two wires. It was tricky, for me, to pull apart the old wires. Luckily, a friend was braver than I, and just pulled them apart using a little muscle, and easily connected the new wires. I screwed it back in, and it was done! I was really impressed with how quickly it arrived at my door, too.