PFSF6PKXGBB General Electric Refrigerator - Instructions

Unscrew old filter and remove(counterclockwise). Line up arrow on new filter with arrow on connection housing. Turn clockwise till resistance met. Do not overtighten. Follow directions. Simple.

First, I have to say I live in the next state over, and I recieved the parts the next day. Yeah! OK, I removed the adjacent drawers *and the removable lower storage shelves on the doors for clearance*. Taking out the broken lid is easy. The new one is a tight fit. The right side has a raised pad on the pivot point, but the left one does not. I worked the peg (pivot point) in on the right side and slowly and carefully pushed the stationary plastic left side in slightly(and sprung the lid slightly) to get enough clearance to get in the left peg without breaking the new lid pivot. While doing this, one has to make sure the shelf immediately behind the lid is in place since there are support tabs located on it, and you will have to rework the thing if you don't get them to mate on the installation.

unscrewed old filter by hand, installed new filter.

Until I figured out that the Metal cover on the divider door had to be removed (pried out) giving access to the hidden hinges. After that the hinges could be removed and replaced.Great with giving phone thou.

opened refrigerator door located water filter location in right back corner unscrewd 1/2 turn and out it comes without shutting off water it is a snap to do by anyone and shipment was really quick thanks. People do not call a service tech for something this simple even a child tall enough can do it.

Nothing to tell it was just a replacement part that the old part was removed and the new one inserted. Works like a dream Thanks

just had to unscrew old one put the new one in

Watched repair video from this site cleaned off shelf, removed the two bins, lifted it out broken shelf, placed new shelf back in, returned the two bins. One step that would have helped a little would have been to remove the bottom door pockets. This would allow the bins to come out easier.

If this repair looks hard then you probably aren't doing it right. The key to doing this fairly easy upper hinge replacement is to pry the metal back off of the swinging panel attached to the door as a first step. Doing so exposes the screws that hold the hinges in the panel, and also the tabs that you must press in to release and remove the hinge covers. I accidentally broke the tabs on both hinge covers removing them, but I discovered that it didn't matter - I was still able to snap them both into place without having to replace them as well. Once you've released the hinge covers slide the panel upwards to reveal the entirety of the hinge, then push the hinge up with a flathead screwdriver so that it slides off of the anchor piece on the door. Slide the replacement part down onto the anchor, slide the swinging panel down and replace the hinge covers. From inside the panel reattach the screws (middle hinge only) and replace the panel parts including the metal back. Whole repair takes about 15 minutes.

Moved stuff out of my way on the top shelf, reached in and turned old filter to remove. Filled new filter with water, lined up and turned to lock in place. Whew, never thought I would get that job done. :-)

Unscrewed old cartridge, ordered new cartridge, installed new cartridge by following very simple instructions. Took only one day for part to arrive from PartSelect although I paid for cheapest shipping, which was "ground." I was amazed!

Took the old filter out and put the new one in.
Easy Breezy!!

I only had to remove the old filter and install the new one - all by hand. I then ran about 1 to 1and1/2 gallons of water through the filter to clear it.
A WORD OF CAUTION - HOLD YOUR GLASS CLOSE TO THE WATER DISPENSER FOR THE INITIAL FILLING - IT WILL SPIT UNTIL THE AIR IS PURGED FROM THE SYSTEM!!!
An extremely easy repair.

Water flow restrictions. Replaced flow valve. No help. Checked again and found filter head flow stopping valve broken. Replaced same. All good.

Take top two drawers out and install the flip up cover in it's spot , then use the screw driver and pry it flip cover, into the groove.