Models > NFTR18X4QB0 > Instructions

NFTR18X4QB0 Frigidaire Refrigerator - Instructions

All Instructions for the NFTR18X4QB0
1 - 15 of 203
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
door rack was broken
pulled broke rack off, snapped new one in place. Yeah!! No more broken jars on the floor.
Parts Used:
Door Shelf Retainer Bar
  • Lannie from Buffalo, WY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
72 of 91 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The retainer door shelf broke 3 years ago
I just snapped the new shelves in place and !voila! I should've done this years ago.
Parts Used:
Door Shelf Retainer Bar
  • Cynthia from Long Beach, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
63 of 83 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Crisper Drawer Glass Shelf slid out of the frame while being cleaned and shattered.
The repair didn't require any tools at all. Just simply slide the new glass shelf carefully into the the frame and while holding it horizontally slide the frame back into the rails. This took less than a minute to accomplish. Very satisfied with the results.
Parts Used:
Crisper Glass Shelf Insert
  • Ernesto from Porter, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
42 of 52 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator door handle broke at the top of the door at the screw in point.
Removed the old handle and lined up the new one and screwed in.
Parts Used:
Refrigerator Door Handle Set (2 pieces) - Black
  • Lynette from FLUSHING, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
28 of 32 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Glass shattered
Don't ever tell your 11 year old to clean the refridgerator. Something will almost definetly get broken like the glass shelf, but luckily I had parts select which in no time assisted me to find the exact part. I ordered the part, it came quickly and I replaced within seconds.
Thanks.
Parts Used:
Crisper Glass Shelf Insert
  • Adona from Gretna, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
28 of 33 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Kids Broke The Retaining Bar On The Frige.
Simply snap the old ones out and install the new ones. Piece of cake. . . . . And saved some $$$.
Parts Used:
Door Shelf Retainer Bar Door Shelf Retainer Bar
  • John from Eden, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
24 of 26 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator not cooling, Freezer working fine
Frig area was at about 50 degrees and would not get cooler. Freezer was working great.
Empty the freezer and remove the two screws that hold the back panel of the inside of the freezer on. Pull the panel out and you will see the fan that is mounted to the back of the panel. If the fan is not running, disconnect it (quick connector) and check to see if there is voltage coming to it from the connector (should be 120VAC between the two wires). If there is power, and the fan was not working, replace the fan.

Fan just snaps into the holder on the back panel and plugs into the quick connector. Make sure you clear any ice build-up in the hole between the freezer and the frig that the fans blows through. Put it back together and verify the fan runs.
Parts Used:
Evaporator Fan Motor
  • Roger from TRURO, IA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
21 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light Socket short
- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.
Parts Used:
Light Socket
  • Rebecca from Gautier, MS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
22 of 31 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No freezer shelf came with our new refrigerator.
No long shelf came with our new refrigerator, Frigdaire did not have one so I went on-line from you and it fit perfectly, now everything does not have to be in one big heap.
Parts Used:
Freezer Shelf
  • TRACY from MAPLE GROVE, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
19 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My fridge temp was warm. Freezer temp was ok, but fluctuated some.
I checked the dampener, it worked. The compressor and fan worked. I knew because my freezer was still hovering around 10 degrees. Coils were clean. Thermistor was the only thing it could be. Took all my shelves out. Removed four screws. Took the back panel off. The thermistor sits tucked in on the side. I piped it out, in clipped it. Used my multimeter to test the numbers. Numbers were off just a bit. Ordered the part. Crossed my fingers.,took less then 5 minutes to put the part in. Plugged in the fridge. It was sitting at 33 degrees in about an hour and a half. I can’t believe I fixed it. I knew NOTHING about refrigerators. For how big my fridge is, it would have cost 3,000 and up to get a new one with the same cu ft size. Instead, it cost me $44. That includes shipping. Thank you Parts Select!! Made it so easy to pick the correct part for my model fridge!
Parts Used:
Temperature Sensor
  • Cindy from AMARILLO, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
24 of 38 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Plastic Frame On Glass Refrig Shelf
Removed shelf from packing, washed it, slid it onto the refrigerator shelf rails and done. Took longer to unpack the shelf than install it! Very easy, perfect fit, and very happy with the exact replacement. Super careful packing, quick shipping. Very good experience. Hope I don't need anymore parts, but if I do, I will definitely get them here.
Parts Used:
Refrigerator Shelf (Spill Safe) - White
  • Linda from Rural Hall, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
17 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic support rim on glass shelf broken
Removed replacement shelf from delivery box. Took items off of existing, broken shelf. Removed broken shelf. Slid new shelf into place. Placed items onto new shelf. Took the rest of the day off.
Parts Used:
Refrigerator Shelf (Spill Safe) - White
  • Patrick from Arlington, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
15 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
rack door broke in half
Rack door slid into place easily. Repair required no tools and took maybe 20 seconds to install!
Very easy job!
Parts Used:
Door Shelf Retainer Bar
  • Lisa from Milwaukee, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
15 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
cracked bottom hinge
My 4 year old grandson used the frig door as a swing.The bottom hinge cracked, then the door wouldn't seal. I propped the door up with some books, removed the broken hinge (2 bolts) and replaced with the new part. Simple fix on the door, only time will fix the 4 year old!
Parts Used:
Lower Hinge Bracket
  • LEE from LEO, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
14 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic fan broke
took the cover off
(cardbord) the fan will come off and go back on by hand no tools needed i changed the fan motor just to be sure. 3 little screws hold it on. the plug only goes on one way u can't mess it up.very easy job u shouldn't have any problems doing it.Jim
Parts Used:
Condenser Fan Motor BLADE-CONDENSER FAN
  • James from GLEN FLORA, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set, Wrench set
13 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the NFTR18X4QB0
1 - 15 of 203