This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.00
In Stock
Order within the next 11 hrs and your part ships today!
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.10
In Stock
Order within the next 11 hrs and your part ships today!
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to...
$22.68
In Stock
Order within the next 11 hrs and your part ships today!
This lid hinge is a genuine OEM replacement part for your washing machine. This hinge is for the left side of your lid, although it is a good idea to replace btoh hinges at once. The hinge holds up th...
$25.32
In Stock
Order within the next 11 hrs and your part ships today!
Questions And Answers for MVWB765FW1
Ask our experts a question about this model and we'll get back to you as soon as possible!
7 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Francisco Zargoza
December 11, 2019
Hi my washer will not start on the screen only get the code f5
For model number MVWB765FW1
Hello Francisco, thank you for writing. This is due to a faulty Lid Lock Assembly, part number PS11722981 for your model washer. Good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Bruce
November 15, 2023
Machine won't turn on but there is a green light in the back that flashes
We unplugged it gave it some time plugged it back in and the same thing happens
For model number MVWB765FW1
Hi Bruce, thank you for contacting us. The light tells you that the main control board is getting voltage to it. If resetting the unit does not solve the issue, then you may need to replace the control board, part number PS16875371. We hope this solves your problem!
I do not get any hot water on hot water setting except for clean with affresh cycle. Check hose for blockage ok
For model number MVWB765FW1
Hi Peter,
Thank you for your question. If you are not getting any hot water on any other setting except the clean cycle, there are some parts that you will need to check to see which one is causing the issue. You will need to check the water inlet valve, the lid lock assembly, the electronic control board, and the water level pressure hose. We hope this helps! Good luck with the repair!
I have a Maytag Model MVWB765FW1. I don't know if this is a high efficiency because it was in the house when I bought it. Need to know for type of detergent. It's a top load.
Also, I've seen in the question section a lot of people have trouble with the white residue on dark clothes after washing. I've tried all the suggestions to no avail. However I put these particular items through the dryer anyway and it came out looking fine after the dryer. If you have any other thoughts on this issue please put me on the list to let me know.
For model number MVWB765FW1
Hello Joni, thank you for reaching out. Based on our research, we would recommend using only high efficiency detergents. A white residue may be the product of using too much detergent per load, especially if the water is not hot enough for the detergent to dissolve. Using the high efficiency detergent will most probably solve the issue. We hope this helps!
Was this helpful?
Thank you for voting!
J
February 8, 2024
Any dark clothes come out with white streaks all over. I use liquid laundry detergent and it's HE. I use warm water. I even ran it through the whole cycle again with no soap and it still had the white streaks. I don't think it's due to body oils because it's all over the whole garment.
For model number MVWB765FW1
Hi J, thank you for the question. We would recommend using the proper amount of the detergent. If the issue persists, we would suggest checking the dispenser drawer, part number PS11770104, for any leakage. You may need to replace it to fix the issue. We hope this solves your problem!
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
1.) disconnect power to your washer. Turn off water supply and disconnect from the washer.
open the washer top and remove plastic cap from the wash plate
2.) using 7/16 socket, remove bolt from the wash plate. If you can't remove it with a socket , I recommend using impact wrench.
3.) remove wash plate
... Read more( you might need to spray penetrating oil or wd40 inside the bolt hole to loosen it. Check to make sure the wash plate gear grooves are not worn down, if they are, replace it.
4.) using your Maytag specific spaner nut wrench, remove the spaner nut from the shaft of the gear case. This should be right underneath where the wash plate was. If you can't turn it by hand , use a rubber mallet or hammer to encourage it.
5.) some people remove the wash basket at this point. I don't think it is necessary.
6.) close your washing machine. Tape the top closed to keep it from flying open. Tilt your washer back and prop it up where you have access to the underside of the washing machine.
7) remove motor rotor bolt and pull rotor off of the motor.
8.) disconnect the two wire connectors that supply power to motor. using a socket, remove bolts that are keeping motor attached to the gear case.
9.) Now that the gear case is all the is remaining on the underside, you can remove the 4 bolts that are holding the gear case to the washer. Now try to pull gear case out.
10.) if gearcase will not pull out, lower washer back to upright position. Spray penetrating oil or wd40 around the shaft of the gearcase and allow it to sit for 5-10 minutes. Using a hammer, lightly tap on the shaft of the gearcase and it should now fall out. ( you might have to apply penetrating oil again, or apply more force with the hammer.
11.) reinstall motor to new gearcase. Insert new gear case to the washer. Reinstall bolts and reconnect power supply wires.
12. ReInstall spaner nut inside the washer, reinstall wash plate.
Raised lid to remove two Torx head screws from each hinge. Lid will then lift off of hinges. Installation of new lid was the reverse of the removal procedure. It is best to install one hinge to the lid by removing that hinge from the washer. The lid can then be installed by inserting that hinge into it's spot and then over the other hinge
... Read more. Install the hinge screws into the second hinge and the job is complete. The lid now closes properly allowing the automatic lid lock to function properly.
