MGR5770ADW Maytag Range - Instructions

I removed the door from the oven and set it on towel on the table, and started the repair of the door. I removed the screws one at a time, and one layer at a time. Becareful you need to take the whole door apart, and remember how it goes bact together. In the end it was worth it. The hardest part was getting the right part. I thought I could order the whole door, and found out after several calls they don't sell the whole door. Part Select both times I put in my order had the parts at my door within 2 to 3 days. I also had to return one of the parts and within 2 to 3 days the part was credited to my account

The burners turn and lift. I replaced two. One turned very easily, the other was stuck so I used liquid wrench and plumbers pliers. I did get it off. Once off, the old wires slipped right off and onto the new burners. Those twisted on very easily. Good as new easy breezy.

First I unpuged the Range. Then I removed all racks and bottom tray of oven.
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I turned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !

Turn off the gas supply and unplug the power cord. Remove the screw on the back plate for the metal tab that covers the valve. Bend the tab up to expose the valve. Remove the gas line that feeds the broiler with an adjustable wrench. Remove the mounting screw for the valve. Loosen the valve inlet gas line fitting with an adjustable wrench. Lift the valve out. Reverse the steps to install the new valve.

I removed the screws from the top of the door, the sides and the bottom of the door. I still couldn't get the door to come apart because there were screws on the inside. It took me about 10 minutes to figure out that I had to slide the glass plate off the front of the door to get at the screws on the inside. Once that was done, I was able to replace the handle without problem. The only other thing is that I cut the top of my index finger while trying to clean the door before I put it back together. I was careful to keep track of which screws went where because otherwise it would get confusing. My handle looks and works great! Thanks

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.

removed 5 trim screws from the perimeter of oven door, inserted new glass, reinstalled - done!

It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison

Had to unplug unit, remove back of unit (6 screws), then unscrew oven sensor (2 screws), then unplugged old sensor, replaced it and put back of oven on...Moving the oven out and working in the tight space avaialble was the most difficult. Other than that, super easy job that probably saved me a lot of $$$...

After reading some of the repair stories, I was hesitant about doing this task. It was really very simple, I just removed the screws from the back of the stove, and removed the old element. I then replaced it with the new one and replaced the back cover. This whole task from start to finish took 10 minutes. The oven heats perfectly now just like a new oven.

needed to completely dis assemble the oven door to get to the inner pane of glass...took some time...I was able to do it on my own...could possibly go a little quicker with two people for a few of the steps...but possible by one...then reinserted the glass pane...and then need to re assemble the door layer by layer...up and working again...would have cost several hundred dollars if need to call a repair person in...this way was the cost of the piece..less than $70 ... and my time...well worth it....thanks

Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.

Parts came very quickly from PartSelect. Good service.

Lifted off the door, unscrewed all sides of the door attached the handle to the new trim, and screwed everything back together. It at first was not obvious how to remove the old trim, but the trick was to unscrew all sides of the door (bottom, top and on each side). The door just lifts right off easily. Then you unscrew the old trim and screw in the new trim (be sure to attache the handle first!), and then reinstall the sides and front glass by sliding into place and put back all the screws.

Then slide back on the repaired door.

The part didn't come with installation instructions specific to any stove/oven so I went by a previous testimony on this website and pulled out the stove, and started to remove the side panel to get access. Well turns out I could have done the whole repair in place because on my Maytag the igniter source is accessible by removing the utility drawer and it's mounted on a small galvanized steel panel at the left side which hides the part directly. The existing spade connectors were the right size for me but I did have to crimp them tighter (which was perhaps part of the initial problem). After installation, the spark is much more powerful and all burners lit first couple "clicks".