Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Drum belt broke
Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on. This was a first attempt ever at fixing an appliance and it was no big deal.
Leaking washing machine; water would not shut off on fill up and rinse
Replacing the switch is relatively easy, however, I would caution all experiencing similar problems one thing. Before assuming, as I did, that the switch was bad, first remove the panel of the washer that houses the washing tub/basin. On the back of the tub, check to make sure that the tube connecting the tub and switch has not come off from the tub as it did in my situation. The solution to my problem of a leaking washing machine where the water would not stop filling on both wash and rinse cycles was simply reattaching the tube to the tub. If I would have checked that first, total job completion time would have been under 15 minutes. Hope this helps. If you need to replace the actual switch, remove the knobs, screws, and panel. Remove the wires, tube, and screw from the switch and reassemble new switch. That took me about 30-45 minutes.
The Lid Lock Assembly came super fast! The install would have been flawless, but the "pre-drilled" holes on the new Lid Lock Assembly were way to small. We found that out after we had reconnected the wires and gotten it into place. Aside from that small set back, the install went great! This repair is definitey not one that you would need to pay a repair person to do!
I had to take most of the dryer apart because there is no rear access to the motor. It turned out to be easy to dissasembel the dryer. The only problem that I had was that I could not figure out how to route the belt around the motor and the idol pullies. I could not find anywhere that gave instructions on how to properly tension the belt. I finally figured out that the idoler pulley needs to be locked in place on the right side of the engie mount. Then the belt needs to be routed over idoler pulley and under the motor pulley. Finally release the idoler pully from the locked postion to put tension on the belt. It really turned out to be pretty easy.
Pryed off the top with a flat head screwdriver and removed the 2 screws holding the front panel to the sides. Then lifted the front panel off of the bottom brackets. Belt fit perfectly and followed the provided instructions to loop it around the motor and pulley. PartSelect got the part to me within a couple of days and the repair was a snap.
removed upper cover, removed front cover, tested switch with digital VOM, removed and replaced! 2 screws, 4 wires! saved over $100 when compared to a bill from a repair service!
first removed the 2 screws disconected the terminals, installed new switch connected wires back and test washer and it worked like new, i put a Jumper to get the washer to work while i got the parts. Also i received the parts in 24 hrs. Thank You.
Washer machine would fill up with water and not spin and drain
Happened to slam the lid by mistake and the washer started spinning. Recognized the lid lock was working haphazzardly. Also, there was a burning type odor coming from the switch. So I lifted the lid top and disconnected the switch from the lid by unscrewing 2 screws and 4 wires. When I received the new switch, I reinstalled it with 2 screws and reconnected the 4 wires.
1st - removed the two screws inside the front door panel. They are somewhat hidden up underneath so you may have to look for them. 2nd - I removed the top of the dryer cabinet by lifting it out of the clips holding it in place. 3rd - removed the two screws (one on each side) in the o=uppper corner of where the side panels connect the front panel. These are about 3/4" phillips head screws. Then the front panel could be moved to one side of the dry. 4th - remove the drum by lifting it up and out the open top area. 5th - add the new belt to the dryer tub (rib side towards the drum) and replace dryer tub to its original position. 6th - reaching in underneath the tub you need to pull the ideler pulley toward the center of the cabinet while laying the belt on the "outer side" of the ideler pulley and at the same time fitting the belt over the small pulley located on the motor. Once that is done, you reassemble in reverse order and should be good to go.
This is the second time in the same 7 year old appliance. Remove the front bottom cover by removing 2 screws. Then remove the 2 screws holding the pump down. Then unclip the electrical wire from the pump and remove both hoses from the pump by squeezing the spring clamps with a pliers. Have a pan to collect the water that will drain from the lines. Take the new pump and install it in reverse order from above.
Control knob had broken and we were unable to set the dryer
I first ordered the replacement knob. It had broken before and I had repaired using a steel washer and epoxy to support the cracked plastic. When the support system I installed broke, I suspected a deeper problem; increased resistance to knob rotation in the control system. I removed the front panel to get back at the switch area. I wanted to lubricate the whole control, but UT seemed to be well sealed. Finding a couple areas where the plastic came together, held by a permanent metal mount, I used a pressurized silicone lubricant and sprayed into the small spaces. That allowed for easier rotation of the control, hopefully giving a longer lifespan to the new knob. DO