Models > MEDB835DW4 > Symptoms > Not Heating

Parts That Fix Whirlpool MEDB835DW4 Not Heating

Not Heating is a commonly reported symptom for the MEDB835DW4 Whirlpool , and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your MEDB835DW4 Whirlpool that will fix Not Heating. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!

1 Dryer Heating Element
Fixes Symptom 70% of time
Dryer Heating Element – Part Number: WP3387747
★★★★★
★★★★★
139 Reviews

Rated by 58 customers 

  

Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.   

When connected to electricity the dryer heating element glows red hot and generates heat. When air is blown over it, it heats the air which is used to dry the clothes. The heating element fits inside the heater housing inside the dryer. Wear and tear on the heater coil from use will eventually cause the coil to break and the element to fail. When this part fails it can cease to produce any heat. Alternately, the coil could break and short to ground allowing the dryer to continue to heat even when turned off. The latter is a fire hazard and the dryer should be disconnected from power until the element is replaced. If the element coil breaks, the element needs to be replaced. This model is 11 by 5 inches with 5/16” terminals, metal and ceramic, and comes in black. It is sold individually.

$ 94.64
  In Stock
PartSelect Number PS11741416
Manufacturer Part Number WP3387747

Replacing your Kenmore Dryer Dryer Heating Element

Replacing your Dryer Heating Element

Customer Repair Stories

Dryer would not heat at all.

Found a service manual on-line for the Whirlpool Duet Dryer. Did the troubleshooting for the problem stated. Found the heater element to be bad (open circuit across heater block). Ordered new element from PartSelect.com and installed. Dryer now works like a charm and I didn't have to call a repairman.
  • Lou from Orlando, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
35 of 38 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Burned out heater element

Remove the kick plate from the bottom of the dryer by sliding a putty knife along the top edge to release the plastic clamps, one on each side about 4" in from the edges. The kick plate folds out and down. You will see the heat shield on the right, held in by one hex head screw. Remove screw and heat shield. The element is positioned in an open-front housing and is fastened to the left side of the housing by two hex head screws, located on the "rail" of the element and right near the two wires. Remove the hex-head screws that hold the element in place and disconnected the two wires by pulling them out by hand or with needle nose pliers. The only difficulty here is the cramped working area...I recommend a stubby socket driver for these two screws. Most of this I had to do by feel because I could not see the screw heads. Once the screws are out and the wires have been disconnected, slide the old element straight out toward you. You may need to disconnect a small plastic hose located to the left front of the element, but this hose just pulls right off. Vacume the dust & lint build-up out of the whole area, wipe out the element housing and clean up the whole underside of the dryer prior to installing the new element. Installation is reverse of removal. It also might be a good opportunity to clean out your exhaust duct and the vent to the outside. (Never use the aluminum foil-accordian-type duct.) If the exterior dryer vent has any kind of screen over it, remove it and get rid of it. Screens collect lint, lint builds up and burns out elements.
Read less
  • Alan from Brooksville, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Socket set
492 of 575 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2 Thermostat, Internal-Bias
Fixes Symptom 23% of time
Thermostat, Internal-Bias – Part Number: WP8577274
★★★★★
★★★★★
30 Reviews

Rated by 30 customers 

  

Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.   

The internal-bias thermistor (Thermistor, Dryer Thermister, Dryer Thermistor) prevents the dryer from overheating by monitoring and controlling the temperature of the inside of the dryer drum. It is located on the blower housing, next to the thermal fuse. If your thermistor is defective, drying time could be prolonged or you could get a fault code. You could also notice your dryer overheating. You can test the outlet thermistor on a multimeter, it should read 10Kohms (10,000 ohms) of resistance at room temperature. It can tolerate 10% fluctuation. If your reading indicates the part is defective, it will need to be replaced. This model is white plastic. It is sold individually.

$ 47.74
  In Stock
PartSelect Number PS11746740
Manufacturer Part Number WP8577274

Replacing your Whirlpool Dryer Thermostat, Internal-Bias

Replacing your Thermostat, Internal-Bias

Customer Repair Stories

Dryer turns off after 1-2 minutes

I tried to follow directions followed by others on this site after diagnosing the problem via suggestions provided by users. I have a Whirlpool Duet dryer from 2002. We've had problems since moving about 3 years ago. I removed the front panel (lower) by unscrewing the two bottom screws (1/4" sheet metal screws). Then I took out the lint screen and the metal tube/contraption immediately beneath to get access to the area where thermistor is located. See the drawing/chart to help you locate this. It's really easier than it seems. Make sure you have the chart/drawing for your model - it makes difference! The thermistor came out pretty easily with a nutdriver that has a swivel offset shaft. Ask your hardware store tool dept. about that one. Put everything back in reverse order of course and test either with/without the front panel re-attached. In my case it fixed at least part of the problem. I was able to get clothes almost dry with most settings but I have yet to install the moisture sensor to see if that helps in addition to the internal-bias thermistor. I am the kind of person that does one thing at a time so at least I now know the thermistor was bad. Good luck and hang in there with your own repair. It's a lot cheaper even if it takes you longer to do than a pro.
Read less
  • Dixon from Santa Fe, NM
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
19 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Unit would shut down in the middle of cycle and flash E1 trouble code

Had to remove the back of unit to access the area of subject part by removeing 12 to 14 screws also the gas line had to be removed. Two screws held the part in place. Unit now runs normal.Saved alot on repair costs!!!!!
  • Jim from Tucson, AZ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
30 of 40 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
3 Heating Element Connection Wire Kit
Fixes Symptom 8% of time
Heating Element Connection Wire Kit – Part Number: 279457
★★★★★
★★★★★
3 Reviews

Rated by 10 customers 

  

Really Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.   

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

$ 11.06
  In Stock
PartSelect Number PS334206
Manufacturer Part Number 279457

Replacing your Whirlpool Dryer Heating Element Connection Wire Kit

Replacing your Heating Element Connection Wire Kit

Customer Repair Stories

Dryer stopped heating

(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.
Read less
  • Joseph from Austin, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!

couldn't get the wire connection anywhere after we bought the heating element.

we received the two heating element wires in 3 days and connected the heating element with no problem works great.
  • Betty from Erie, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Back to Top