MDE17PRAYW1 Maytag Dryer - Instructions

Part came in about 3 days. After reading and checking what was wrong with the Dryer -- which i read if there was no noise coming from the dryer it was the door switch, Looked up the part number and then saw a video that showed how to install the door switch. The video was so informative and precise on everything you had to do and easy Saved money on a service call.

sounded like a pair of shoes was in the tub every time i started it no matter what size the load was. Replaced the back two rollers first and decided to start it to see how it sounded. We were glad. Only the back rollers were bad and the dryer was quietly running again. We would suggest replacing the back rollers first to everyone because the front rollers are more complicated to replace and they may not have to be at all.

Removed two hex screws from upper back clips. Removed 2 Phillips screws under lint trap. Used flat head screwdriver to pry up top on front right and left side clips. (FYI: top pry's up off retaining clips in front). Remove two hex screws on right and left front panel. Un-plugged wire harness front right side. Lifted up and removed front panel. This hold the drum in place. Simply removed drum, installed new belt, replaced the two drum wheels and put everything back together the same way I took it apart. 30 Minute project :)

I Picked up the two front corners up, after removing the 2 screws from the vent and the 2 screws that hold the door switch in place, then I disconnected the old switch and put in the new one. Just the opposite of how I took it apart. Very simple and it works great!! Thanks

It is odd that this part needed replacement but I am in an area near the Atlantic ocean in a vacation house which is vacant most of the year. The exhaust vent probably brings excessive moisture down to the dryer in the basement. The screen you can see at the inside back of the tumbler (where the heated air enters) rotten out, pieces fell inside and there was danger of something falling in and catching fire. I found no useful source for information (including YouTube) as this part is most easily replaced from the rear of the dryer and the available info was about repairing the heating element, the circuit board, or the exhaust venting pieces which is done from the front.

The bottom line is that the back removes easily. You should:
1. unplug and remove the exhaust shoot
2. remove the top per YouTube or other source
3. take off the back panel over the electrical connections and unscrew the ground; tuck it inside. Don't undo any electrical connections except the ground
4. take off the screws holding the back on (8-9, one is hidden above the exhaust vent) and pull it out of the way; you then have compete access to the "DUCT-AIR" part
4. undo the clip that holds the vent tube (from the heating element) to the part
5. remove the screws that hold the part to the inside back (3?) and push it out of the way
6. remove the clips and remove the old part
7. reassemble in reverse order

I'm over 70 so I took lots of time and breaks but was still done in under two hours. The 2 clips holding the heater element tube to the part were badly rusted and should have been replaced but I made do with the old ones.

Just like the video, just followed the video
Thanks,

I removed all the panels, removed the tub, replaced the pulley, put the tub back in and replaced the panels. Just when I screwed the Last screw in the doorbell rang with the door switch which I installed immediately.

Remove screws, dryer sensor on screen. Put sensor back in place. Secure with screws. The way you take it off go in reverse.

Noticed the door switch was loose and the light bulb inside dryer didn't stay on. Researched the problem on PartSelect. Followed the directions given: Take 2 screws out of top of lint trap. Pry top off of dryer with putty knife. Unscrew 2 screws in dryer door frame holding in old switch. Uplug and remove old switch. Plug in new switch and put screws back in. Close top of dryer. Reinsert 2 screws in lint trap. My 20 yearn old dryer works!

There are many good youtube Kenmore/Whirlpool door switch replacement demos online. The one already done by this site )was close enough for me. I could see that the door switch on my dryer was bad (the plastic part that the door makes contact with was visibly broken, as seen from the outside) -- so I ordered a new one. You don't have to open the top fully to access the switch wiring harness -- i propped it open with a roll of duct tape, The hardest part for me was to disconnect the old switch from the harness (I used a small flat bladed screwdriver to free it). Be careful, the metal inside the opened dryer is sharp, and can cut you.

I followed the video provided by ‘Partselect’; although it was not the exact model it was close enough to get the job done with high confidence.

1. Didn't understand how to do continuity test for 3-wire door switch. After looking that up, I discovered that wasn't the problem ! I have tested, the thermal fuse, oscillating fuse,start switch, I've tested the timer and the black , blue connections go to zero ( continuity good) the tan , white connections just barely off of infinity. I've ordered a new timer. I'll let you know if that's the problem. If you can more diagnostic videos. AKH

Remove the lint screen, then remove the two (2) Phillips screws that are at the entrance of the lint screen compartment. Take a putty knife and insert it under the top pannel of the dryer about 1” in from the outside and push the putty knife in as you lift that corner of the pannel. Repeat on the other side. Then raise the lid and prop it up. The door switch is on the right side just behind the door on the inside. Open the door and remove the two screws that hold the switch and remove the switch. Install the new switch like the old one came out and close it up you’re ready to go! It is very easy you can’t hurt anything.

First removed lint screen, then removed screws holding lint screen housing.Pushed on back of machine a little so that top could be pried up. Then replaced switch and put everything back together. Helps to have two people so one can push on back of top piece while top of machine is being pried up.

I just followed the instructions from this site for the door switch part and had it running in 10 minuets. This site made it very easy.