MDE17MNAGW0 Maytag Dryer - Instructions

Just follow the repair video, it was easy!

I removed the two screws underneath the lent trap the removed the two screws that held the dryer switch assembly. I then lifted up the top and disconnected the door switch assembly. Removing the door switch assembly was the toughest part, and it was not difficult. Simply grab a pair of pliers and pull. I the attatched the new door switch assembly and the four screws and my dryerwas as good as new. I paid around $20.00 including shipping and saved myself a couple of hundred dollars

Removed old door switch and tested with ohms meter. It registered as charged, but when black button was pushed it did not cut off (go to zero). Replaced the part just like the video showed. Only problem i had was dropping my screwdriver down into the dryer well. It was doing no harm so i left it there since i tried retrieving from the back but was not able to get entire back off!

Kill power to dryer from breaker box.Remove lint filter & 2 screws. Take a flat head screw driver and place in gap between rash from corner of top panel & front panel of dryer and pry up to raise top panel of dryer & rest against wall the wall on angle do it doesn’t fall back toward you. Unplug wiring harness from dryer switch inside top front corner of dryer with outside of drum exposed when top panel of dryer is raised. Open dryer door and remove screws on each side of dryer switch located at upper inside corner of door opening. Take flat head screwdriver had slide in between connector & wiring harness on dryer. Remove old switch. Reconnect new dryer switch to wiring harness & remount switch to inside of dryer door opening. Lower top panel of dryer & press front corners of top panel to front panel of dryer & clips will be locked in place. Replace screws in dryer filter mounting holes yo top panel & replace dryer filter in place. Turn on power ‘ & check if light is working 1st. Then, turn timer knob clockwise, close door and listen if the drum is turning. Open door to see if drum turns. If both work, the job is complete.

Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.

This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.

"YOU MAY NEED A LICENSED PROFFESIONAL TO MAKE THESE ADJUSTMENTS." Gas cooktops come set for natural gas (NG) regulator and buds. The size of holes are smaller on propane gas (LP) buds than NG buds. New gas appliances often come with both types of buds in the package. This one did not. The hard part for me was to figure what size bud goes in each burner. The universal kit I purchased from PARTSELECT.COM came with no instructions. Just a bag of buds stabbed onto a color coded card. No explanation for size of each color on the bud's card. Though a drill bit will reveal the hole size, I still did not know which size hole fits what burner. 45 minutes of research on line revealed the chart with the solution. Once a bud's burner location was revealed, it took three minutes per bud using a mm socket to swap out the NG buds for LP buds. Each burner has different size hole in the bud for flow temperature on the burner. 5k BTU or 7k BTU or 12K BTU burners. Swapped the flow restriction valve on the regulator by removing the cap screw on the regulator. Flip the valve to LP and reinstall the cap screw. The new appliance was ready to be installed. Follow connection rules for gas fittings and turn on gass.
No sweet smell gas, squirt joints with soap solution to check for leaks. Do not light burners until leak check is verified no leaks. No leaks detected. Light each burner. Check flame. Works as advertised "YOU MADE NEED A LICENSED GAS PERSON TO PERFORM ALL OF THIS MAINTENANCE."
SAFETY FIRST!!!

The pulley is accessible from the back of the dryer. Disconnect the gas line. Remove all the screws. Also remove the small plate that secures the line cord. Lift the back up and out. I was able to avoid disconnecting the water line. Take a picture of the pulley so that you will have a record of the belt routing. Release the spring and remove and replace the pulley and bracket. Vacuum out the lint. Plug in the dryer to make sure that it works properly before reassembly.

After getting the part and sizing up what to do. I removed the 6 1/4 hex nuts from the back. I removed the 2 hinge nuts 3/8 and popped the lid of the dryer up. It wasn't coming up all the way. I removed the lint filter and removed the two #1 Phillips screws that held the lid to the duct and it came up easy.The switch itself was clipped together and came apart with ease. 2 #1 Phillips screws held the switch in place and quickly tightened down the new switch. I clipped the new switch to the old lead and just reversed the order putting it back together. The light worked and the drum stopped when the door was opened during the cycle. The part matched perfectly and there was no guess work about clearance. It was an easy repair.

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

Determined that the door switch was not making contact. Removed the lint screen, removed two screws in the lint screen housing, pulled the top of the dryer up at the front of the dryer. This provided access to the door switch which was mounted on top.

The brightness of the light was because the door switch was allowing too much current to the light bulb when the door was open but the switch would not swich the current to the dryer motor when the door was closed. After a day or so of this bright light it burned out. I removed the two screws on top that hold the lint trap in place then I could access the switch by sliding the top of the dryer forward and lifting the it as you would lift the hood of a car. The switch is on the right side and plugs into a three wire connector and only fits in one way. Cheap and easy fix after unplugging the dryer from the wall power outlet.

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.