Models > LWD973

LWD973 (P1110502W) Amana Washer - Overview

Sections of the LWD973

[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Single Washer Inlet Strainer – Part Number: WP22002960
Single Washer Inlet Strainer
PartSelect #: PS11739405
Manufacturer #: WP22002960
Found at the end of the inlet hoses.
$11.06
  In Stock
Water Inlet Valve – Part Number: 33930
Water Inlet Valve
PartSelect #: PS2037023
Manufacturer #: 33930
This washing machine water inlet valve has two ports for water to enter.
  No Longer Available
SLEEVE,LONG – Part Number: 24128
SLEEVE,LONG
PartSelect #: PS69128
Manufacturer #: 24128
  No Longer Available
SLEEVE,SHORT – Part Number: 24129
SLEEVE,SHORT
PartSelect #: PS69129
Manufacturer #: 24129
  No Longer Available
SCREW – Part Number: 25817C
SCREW
PartSelect #: PS70026
Manufacturer #: 25817C
  No Longer Available
DIAPHRAM – Part Number: R0606506
DIAPHRAM
PartSelect #: PS534787
Manufacturer #: R0606506
  No Longer Available
ARMATURE – Part Number: R0605511
ARMATURE
PartSelect #: PS534791
Manufacturer #: R0605511
  No Longer Available
ENCLOSURE,MIXING VALVE – Part Number: 33098
ENCLOSURE,MIXING VALVE
PartSelect #: PS542762
Manufacturer #: 33098
  No Longer Available
GUIDE,ARMATURE – Part Number: 24130
GUIDE,ARMATURE
PartSelect #: PS552297
Manufacturer #: 24130
  No Longer Available
SPRING – Part Number: 23224E
SPRING
PartSelect #: PS552424
Manufacturer #: 23224E
  No Longer Available

Questions And Answers for LWD973

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water Inlet Valve Damaged
The Speed Queen people were nice enough to provide a swing out door on the back of the machine to access the mixing valve. I had to pry it open because they did not supply enough slack in the hose that attaches to the mixing valve. The hose clamp securing the outlet hose to the valve was difficult to remove as the screw was positioned by someone that assembled the machine with no thought given to if it would ever to be taken apart.

Be sure to unplug the machine before attempting this repair. I unplugged the dryer instead and was greeted with a shower of sparks as I removed the valve. Luckily there was no damage to me or the machine. I needed some lubricant to slide the hose onto the new valve. There was some Linatone oil for my dog's coat handy. It did the trick I buttoned the machine back up and it works as good as the day I bought it.

It might be wise to replace the gaskets between the water hoses and the inlet valve. They are just standard garden hose gaskets. Replacing the strainers on the faucet side might be a good idea also. I took a video of the Speed Queen in action and will post it to You Tube. "They Don't Make 'em Like This Anymore"
Parts Used:
Water Inlet Valve
  • Ronald from Arcadia, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
9 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad tube seals and bearings
Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.
Parts Used:
Single Washer Inlet Strainer
  • DAVID from SANDY HOOK, CT
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Socket set, Wrench set
1 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaked into the drum while turned off cycle.
As another person commented, there is a small 'door' on the rear where the water inlet is located. Don't know if this was meant for easy access to change this part or not but I didn't use it. I found it much easier to just remove the front panel (2 lower corner screws), loosen the top (2 corner screws) and tilt it up and out of the way. From there it was easy to disconnect the hoses and four electrical plugs (easy to remember the order). The unit is held in place by one screw which is located between the water inlets.
Parts Used:
Water Inlet Valve
  • Brian from Evansville, IN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!