LW4303W Amana Washer Parts and Repair Help
Models > LW4303W

LW4303W Amana Washer - Overview

Models starting with LW4303W

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
(2)
PartSelect #:PS11740482
Manufacturer #:WP233520
This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below....
$6.36
In Stock
PartSelect #:PS11740487
Manufacturer #:WP23748
The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has s...
$10.35
In Stock
(6)
PartSelect #:PS12349731
Manufacturer #:W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this sc...
$12.34
In Stock
PartSelect #:PS1594294
Manufacturer #:27001233
This pump is attached to the motor and helps expel water from the washing machine. It is activated after the spin speed is maintained for a specific period of time.
No Longer Available
(2)
PartSelect #:PS11746840
Manufacturer #:WP90767
This screw is sold individually.
$5.24
In Stock
(1)
PartSelect #:PS11743008
Manufacturer #:WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air...
$4.70
In Stock
(3)
PartSelect #:PS11740616
Manufacturer #:WP28808
This v-style drive belt is thirty-two and a half inches long and half of an inch wide.
$22.88
In Stock
(1)
PartSelect #:PS2021026
Manufacturer #:22003428
If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locki...
$8.96
In Stock
(2)
PartSelect #:PS11740613
Manufacturer #:WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washe...
$4.86
In Stock
(2)
PartSelect #:PS11748588
Manufacturer #:WPW10119828
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
$4.86
In Stock
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Frayed V-belt

  • Customer: John from Milton, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 56 of 63 people found this instruction helpful
VERY EASY!!!
SAFETY FIRST-Always unplug the appliance.
Use 8mm socket to remove front panel screws. Loosened up two hose clamps connected to the pump and removed both lines (Hoses contain water, use a towel) which is located underneath the motor. Disconnect motor electrical connector on the left side of the motor. With socket, remove 4 mounting bra... read more

Water leaking on floor from "mysterious place underneath washer"

  • Customer: Bryan from Chicago, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 47 of 52 people found this instruction helpful
Water was leaking on the floor during the wash cycle and especially during draining of the washer. I removed the front panel at ground level and watched while draining after a rinse.

I t was obvious that water was spraying from a hole in the rubber end of the hose (the hose is a fused assembly of a plastic section and a rubber section).

read more

The Seal On The Bottom Of The Tub Was Leaking

  • Customer: HOWARD from CORTLAND, OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
  • 32 of 40 people found this instruction helpful
Removed the front of the washer, then lifted the top up and held it up with a prop. Pulled the agitator straight up and started the disasembly. Using the photos in the hub and seal kit was a big help. The large nut on the output shaft had to be cut off with my dremel tool and the hub removed with a wheeler puller. Assembly was pretty much straight forwar... read more