Models
>
LT170PXA-2
LT170PXA-2 Westinghouse Washer - Overview
Sections of the LT170PXA-2
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Water Inlet Valve
PartSelect #: PS815509
Manufacturer #: 134190200
The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve i...
$127.65
In Stock
V-Style Belt (Drive)
PartSelect #: PS457600
Manufacturer #: 5303261155
This v-shaped drive belt is for washing machines that use three belts and that are loaded in the front. Made by Frigidaire, this belt is 41-1/2 inches long and 3/8 of an inch wide. Use it for your Fri...
$19.93
Special Order
V-Style Belt
PartSelect #: PS457598
Manufacturer #: 5303261151
This v-shaped idler pulley belt is for washing machines that use three belts and that are loaded in the front. Made by Frigidaire, this belt is 46-5/8 inches long and 1/2 an inch wide. Use it for your...
$14.08
Special Order
Questions And Answers for LT170PXA-2
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the LT170PXA-2
[Viewing 2 of 2]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer Continued To Fill To Point Of Overflow
First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and remo
... Read more
ved the water connection to the valve. Then replaced with the new valve followed the above steps in reverse order, finishing up by re placing the water connections and power. Then checked fo proper replacenent and leaks before replacing top panel.
Read less
Parts Used:
-
alvaro from east hampton, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
86 of 96 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No Cold Water
Checked problem on-line and discovered it was the water inlet valve. Matched the part on part select. Com. Finding the part was very easy. Part select had a grid behind the picture to help determine the size and pictures from all sides. Removing the old part, matching it, and replacement took a total of 30 minutes. I now have cl
... Read more
ean clothes.
Read less
Parts Used:
-
Mark from Pittsburgh, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
16 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water continued to flow into machine during spin cycle
After moving machine to an area that allowed easy access to the unit, disconnected the water supply hoses from the inlet valve.
Removed the two screws that keep the back in place, removed the clips that keep the top in place, moved the top over far enough to get the valve out. Removed the screw that keeps the inlet valve in place, di ... Read more sconnected the power supply to the valve, Pulled valve out in order to remove the water outlet hose. Repalced with new vale, and reversed order to install. Works just fine now.
Removed the two screws that keep the back in place, removed the clips that keep the top in place, moved the top over far enough to get the valve out. Removed the screw that keeps the inlet valve in place, di ... Read more sconnected the power supply to the valve, Pulled valve out in order to remove the water outlet hose. Repalced with new vale, and reversed order to install. Works just fine now.
Read less
Parts Used:
-
Howard from Lcolnton, GA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
16 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!