Models
>
LRE30453SW
LRE30453SW LG Range - Overview
Models starting with LRE30453SW
Click on the best match to narrow your results.
- LRE30453SW (LRE30453SW/01) LG Range
- LRE30453SW (LRE30453SW/00) LG Range (Freestanding, Electric ELECTRIC RANGE)
- LRE30453SW (FW1LLGA) LG Range
- LRE30453SW ( 00 ) LG Range (Lg Lre30453sw/00 Electric Range)
- LRE30453SW ( AWHLLGA ) LG Range (Freestanding Electric Range With Evenjet Convection System)
- LRE30453SW ( FWHLLGA ) LG Range (Freestanding Electric Range With Evenjet Convection System)
Keep searches simple, eg. "belt" or "pump".
Thermostat
PartSelect #: PS3530468
Manufacturer #: 6930W1A003X
The range thermostat is also commonly known as a stove, oven, cooktop, or range thermal fuse. This thermostat protects your oven from excessive heating, and will shut the oven heat off if excessive he...
$20.30
In Stock
Temperature Sensor
PartSelect #: PS11732697
Manufacturer #: EBG61305805
This temperature sensor, also known as a thermistor, is compatible with various makes and types of appliances. This thermistor uses electrical currents to detect the interior temperature of the applia...
$87.56
In Stock
FOOT
PartSelect #: PS3635599
Manufacturer #: 4778W1N001B
This is a genuine OEM leveling leg for various models of LG ranges. This leg is used to stabilize and support the range, and if damaged, broken, or missing, will cause your range to rock back and fort...
$18.00
In Stock
Range Convection Fan Motor
PartSelect #: PS7791924
Manufacturer #: EAU61865301
This part is the replacement A/C fan motor or convection fan motor for your range. It is used to spin the fan blade, which circulates hot air through the oven, and ensures even heating. If you notice ...
$109.31
In Stock
Range Oven Relay Control Board
PartSelect #: PS3530118
Manufacturer #: 6871W1N012B
The sub PCB assembly (also referred to as a relay board), is a part for your range. If your oven is overheating, this might indicate that your sub PCB assembly needs to be replaced. You will need a Ph...
$176.42
In Stock
Radiant Heater
PartSelect #: PS3527756
Manufacturer #: 5300W1R004A
This radiant heater may also be known as a radiant surface element and is a part for your range. The function of this heater is to supply heat to the cooking area that is on the top of the range. This...
$109.31
In Stock
Common Symptoms of models starting with LRE30453SW
[Viewing 6 of 6]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Won’t turn on
Fixed by
these parts
these parts
Show All
Door won’t open after self cleaning cycle
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No heat in oven mode
Verified P/N with LG. Took a few days . They sent names of several suppliers, cost was almost double. Ordered part from P/S, here in 2 days. Watched video on you tube. Unplugged, took off back, unplugged bake element, removed power box. The opening for bake element is still attached to rear panel by tiny bits of sheet metal. Used Dremel w
... Read more
ith cut-off wheel to cut thru nibs & deburr opening. this panel has to be removed, it rests on bottom panel & is held in position by power box. Removed bake element carefully, front of element broken, tried to put new element in, would not fit. Had to grind notches in bottom panel down to clear supports on new element. This did the trick. back together quick & no problems. If had to do again estimate less than 1 hour.. By the way am 81 yrs. young.
Read less
Parts Used:
-
Dennis from CARY, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
8 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace Inner Oven glass because it shattered
Go onto youtube, such as https://www.youtube.com/watch?v=-ITkrwhDNMQ and watch similar videos for DYI. The process is very similar to other models.
Once the door is removed, place oven door on a towel or soft place so it does not scratch the door. Unscrew the screws and make sure you notice where each screw goes, so you know ... Read more the process of where each screw goes when you re-assemble.
Once the inner cover is removed, remove the insulation, too so you don't damage it. Use Wet/Dry Shop Vac to clean the shattered glass. (WORD OF ADVICE: I did not remove the insulation and the suction of the Shop Vac removed part of the insulation, so now instead of a quick turn around repair turns into a few weeks repair, because the insulation is on back order 10-14 days from the supplier. DON"T MAKE THE SAME MISTAKE!)
Once the glass has been removed, the new inner glass is replaced, begin by re-assemble the oven door with the correct screws and attached the oven door to the range.
Hope this helps
Once the door is removed, place oven door on a towel or soft place so it does not scratch the door. Unscrew the screws and make sure you notice where each screw goes, so you know ... Read more the process of where each screw goes when you re-assemble.
Once the inner cover is removed, remove the insulation, too so you don't damage it. Use Wet/Dry Shop Vac to clean the shattered glass. (WORD OF ADVICE: I did not remove the insulation and the suction of the Shop Vac removed part of the insulation, so now instead of a quick turn around repair turns into a few weeks repair, because the insulation is on back order 10-14 days from the supplier. DON"T MAKE THE SAME MISTAKE!)
Once the glass has been removed, the new inner glass is replaced, begin by re-assemble the oven door with the correct screws and attached the oven door to the range.
Hope this helps
Read less
Parts Used:
-
Jeffrey from CERRITOS, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
9 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic cover on the control panel was cracking from high heat frying.
The two ribbon cables connecting the panel to the PC board slide into connectors on the PC board, these connectors have small tabs on each end that are pulled up to free the cable connection, then are pushed down to secure the new cable ends. Use a long Phillips bit on your screw gun to reach the screw at the bottom of the PC board.
Parts Used:
-
Charles from SARASOTA, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!