LRBC22522ST (ASTCLGG) LG Refrigerator - Instructions

I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.

I ordered and replaced the ice maker. To replace:

1. Go behind refrigerator and unplug electrical cord and turn off water supply.

2. In freezer locate electrical plug for ice maker. It has two tabs on the left and right side of it. Lift the tabs and pull the plug to disconnect it.

3. Remove the three screws, 2 on top and 1 on bottom of ice maker You can actually leave the screws in place if you loosen them sufficiently and lift the ice maker off of the screws and washers.

4. Install the new ice maker using the screws and plastic washers to secure it.

5. Plug the electrical connector for ice maker into the receptacle. Note: The plug only goes one way and is keyed with different shaped plugs and holes. The wires on my plug naturally fell upside down so I had to turn the plug 180 degrees to make it fit in the slot.

6. Turn on water and check for leaks.

7. Plug back in refrigerator and you should have ice in less than 12 hours.

I had previously watched a YouTube video (do this first!!) on a similar Kenmore model so I knew what to look out for: (1) turned off power, (2) took thin putty knife to slip under outer lip of switch (most screwdrivers are too thick), (3) wiggled switch at front end to release the tab, (4) unplugged from the socket, (5) plugged in new switch, (6) popped new switch back into door, (7) turned on power. Voila !! Super easy. I couldn't believe it.

My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)

Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.

Used a screwdriver to remove covers. Used a blow dryer to defrost coil in freezer. Cut zip tie and removed old controller assembly. Inserted new controller assembly and secured with zip tie. It took 24 hours for the fridge to cool completely. Now it works fine.

I removed the old water valve, disconnected the water tube going in and tube going out to the back of the refrigerator. New water valve bracket different than the previous one which resulted in my having to modify it to fit. Not an easy task as it was preformed metal. Once hooked up, water turned on, and ice maker turned on, the sound I'm getting now is clunking and not making ice. My debate is whether or not to purchase a new ice maker or revert to the tried and true method with ice trays which work every time.

Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.

I called LG and followed the instructions given over the phone. The instructions couldn't have been simpler. Disconnect the appliance for several hours and then connect again. I disconnected the appliance overnight, cleaned out the freezer, and reconnected it. Problem solved. Did not need to call a repairman and did not use the clips.

Pulled the fridge out of its space. Removed a metal shield which covered the bottom 12" of the fridge with a Philips head screw driver. The water valve is on your right. turned off the water to the supply line. Removed the supply line using an adjustable wrench. Removed the water line gong from the pump into the fridge. It is held on with a "C" clip which can be pulled off with needle-nose pliers. Removed the old pump, held with one Philips head screw. Then installed the new pump, reconnected the lines, replaced the metal shield and turned the water back on. Vacuumed the fridge and its space before cleaning up. The ice-maker now works perfectly.

slid screw driver under edge of switch, easy.

Inserted it with my hands.

When the shelf was delivered, all we had to do was open the door of the fridg. and put the glass into place. pretty easy, huh?

very easy, the customer service person was great and very helpful. I will definitely recommend and use again

This was late on a Sunday afternoon. I immediately called the store where I purchased the refrigerator who told me to go on-line for any parts. So I went to PartSelect and was able to find the correct part very easily and then order it. It arrived on Thursday without having paid for any upgrade in shipping time.I am very impressed with this company.