LMV1680WW LG - Instructions

Not knowing which of the switches to replace I ordered all three in the assembly. Replacing the full assembly was easy, first unplug the microwave. Then remove the top cover to access the screws that hold the control panel in place and let the control panel hang. There are two screws that hold the assembly in place - remove those. I used needle nose pliers to pull the wires off of the switches and immediately put the wires on to the new assembly so there was no confusion on what wire went where. Place the assembly back in position, replace the two screws to hold it in, put control panel in place and secure screws. Replace top cover and plug in.

Use a flat head screwdriver or butter knife to loosen the black frame located on the handle side of door which exposes screws that hold handle on unit. Remove screws with Phillips screwdriver, fit handle onto outside of door and tighten screws. Pop black frame back into place and you’re done.

The wrong part was under $20. When I found out I had to replace the whole door for $150. I decided DYI was the way to go. I used JB weld and the door looks and works like a charm. Give plenty of time to cure all water needs to be cured out if exposed to microwaves. No problems so far.

I unplugged the microwave. I did watch a YouTube video to see how the plastic frame around the door could be removed. I used a putty knife to pry it off. The spring was still in good shape, so I hooked it up to the new latch/locker part and onto the microwave. This was just a little time consuming because I was trying to be careful so I wouldn't break anything on the new part. The plastic frame clicked right back on. I plugged the microwave in and it worked right away. If I can do it, you can do it. Sure beat buying a new microwave. Great experience.

Removed the MW from the wall. Took the top screws off the air vent. Then removed the two screws holding on the display. I then moved the display to its side and it revealed the micro switches. I removed the plug in leads from the micro switch one at a time. I did this with all three micro switches only one at a time. I reinstalled everything and plugged it in. No more fans starting when the door is opened.

Removed outer cover

removed lower door switch

installed new switch

Wa La!

I removed the bottom plate which had 9 screws.
than unplug 2 wires to the motor and unscrewed 2 screws, replaced the old motor with the new one and also the coupler. and so far no noise. easy fix. Thanks

Read the troubleshooting section on this site. Figured it was an interlock problem because the food was not getting hot (magentron not turning on) and the carousel was not turning. Did not think both the carousel motor and magnetron failed at same time, thus indicated an interlock problem. The interlock switches are actuated by the door latch. Replaced the assembly locker piece with all three switches (only a $20 dollar part) and microwave was fully operational again. Wife and kids think I am a hero.

Removed some cosmetic panels. Removed the assembly with micro switches. Examined the faulty switch by checking the clicking action of switch. Two others were ok by this method. Replaced the switch with new one. Works fine so far. Thanks to web site and YouTube videos.

TOOK OUT ALL SCREWS FRONT OVER DOOR AND AROUND FRONT FRAME, LIFTED FRONT FACE OFF, FIRST CKD FUSE, BUT FUSE HAS A WHITE GLASS SO DIDNT KNOW IF IT WAS GOOD OR BAD, NEXT THING I SAW WAS THE HIGH VOLTAGE CAPACITOR, BUT CKD YOUR PRICES ON THE PARTS AND THEY WERE TWO OF THE CHEAPEST TO REPLACE, IT WAS REALLY GUESS WORK ON MY PART, SEE I USED TO WORK ON OVERHEARD CRANES IN A FACTORY, I LEARNED WHEN THEY OUIT WORKING IT WAS USALLY EITHER A FUSE OR A CAPACITOR, SO MY GUESS WORK WAS IN MY FAVOR, AND MY MICROWAVE CAME TO LIFE, I THANK YOU FOR THE NICE EMPLOYEES YOU HAVE WORKING AT PART SELECT FOR THEIR HELP AND GREAT SERVICE, DARRELL INGLE , HOUSTON TEXAS

After checking all three switches for continuity I determined that the plastic door lever had warped or gone out of wack. After shutting off power at the breaker box I removed the door, the inside trim piece around the inside of the glass. Removed the black two prong door lever, reattached the new door lever and then reinstalled the trim piece and all screws. Works fine now. Easy fix just make sure your switches are all ok then replace the door lever.

Replaced entire door latch assembly with the three micro switches. Easier to replace entire latch assembly as individual switches do not remove easily from latch assembly. Had trouble removing front panel assembly. Parts ordered solved this problem.

Unplugged the microwave. I opened the door. I used a butter knife to pop the bezel off the inside of the door. I pushed the locker up and to the left and used the butter knife to pry it loose. Disconnected the locker from the spring, and reversed for the installation.

Took the part above the door off. Four screws. Removed the old door. Put the new door on and replaced the part above the door.

removed old cover put the new one in place found right size screw from my tool box, tightened it.