LFD25860SB LG Refrigerator - Instructions

Switched the refrigerator circuit breaker to off. Put tape around the switch to prevent scratches. Wedged the putty knife into the right side of the switch and pried up.the switch and connector popped out. Removed the connector from the old switch and connected it to the socket in the new switch. Stuffed the new switch and connector back into its home. Switched on the circuit breaker. Now we have light in the refrigerator with every opening!

Unplugged the refrigerator, Taped around the edges of switch as I had read to prevent possible scratches, used very thin flathead screwdriver to pry out old switch, unplugged old switch, plugged in new switch, put it back in opening, plugged fridge back in, and I had beautiful light! Hardest part was unplugging the refrigerator!

After noting frost in freezer Right rail started to jam. Noted freezer door was closing crooked. Rail replacement resolved issue. It had been frosting up for some time so Rail must have been broken for a while. Check door seals they were not closing flush.

Food off top of shelf, drawers come out, glass tops come off, lift the whole unit up (can be a little heavy. Tilt sideways to angle past doors (remove door's lower bins as needed by removing food and lifting up). Turn upside down, remove 3 screws from metal rod and remove metal rod (may require prying out with screwdriver). Remove textured plastic top pieces from each side; some flexing is required to get one side up, then the other. Remove two hinged drawer covers by pinching in at their hinge points.

This is your last chance to clear all the walls, floor, and ledges at the bottom of your fridge. Just sayin'.

Put new shelf upside down on counter. Transfer metal rod to new shelf, screw it in. Transfer hinged drawer covers. Transfer textured plastic topic pieces, again putting one side (of each) in first and flexing unit a little to get other side in. Turn right side up and angle back into refrigerator.

Bring shelf flat and push to the back of the refrigerator until it is flush with the back. Lower whole unit until it rests on top of the side rails where drawers slide in. Left side has a tongue that will fit into a 2" or so notch near the front, right side will rest on top of a round bumper. Front coldness control should still operate smoothly. Put drawers in to make sure they glide and close smoothly. Put glass shelf on top and press down lightly to make sure lower shelf is stable and glass fits neatly into its plastic frame. Replace any door bins you removed.

Ta da!

Followed instructions online

Verified that the contact switches were good. Issue was in the main board. Pulled fridge out from wall. Unplugged fridge from wall socket.
Took out 3 screws holding cover of main board. Unplugged main board. Replaced main board and reconnected plugs to main board. Replaced cover with 3 screws. Pushed fridge back against wall.

Replaced old hose and installed the new one. Was very simple with the instructions in your email..... step by step, could not of been any similar.... you guys rock

I took a very thin bladed screwdriver and took the old part out -carefully.
The new part fit in quite easily.

Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.

Unable to complete repair, had to send parts back
Part should have been PS11732074, but got PS11732704- wrong part
This was a substitute part and was 2" too long

Waiting for refund on this part. It cost me $14.50 to return it by UPS!!!

I had previously watched a YouTube video (do this first!!) on a similar Kenmore model so I knew what to look out for: (1) turned off power, (2) took thin putty knife to slip under outer lip of switch (most screwdrivers are too thick), (3) wiggled switch at front end to release the tab, (4) unplugged from the socket, (5) plugged in new switch, (6) popped new switch back into door, (7) turned on power. Voila !! Super easy. I couldn't believe it.

I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.

Super easy. Removal of old shelf and 3 screws was obvious how to put in new shelf. Thank you. Excellent cost, delivery and ease of transaction.

Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.

Took out tray , removed 2 screws, removed old rail and installed new one.