This dishwasher door hinge cable assembly connects the door to the spring. The door hinge cable and the door spring apply tension to the door to prevent it from dropping open too quickly. This part co...
The dishwasher roller assembly connects to the dishrack, and is located in the lower level of the dishwasher. It allows the dishrack to easily slide in and out. If the lower rack keeps falling off the... No Longer Available
The rack roller and axle in your dishwasher allows the dish rack to slide in and out effectively.If you notice that your dish rack is not performing this function, or if one or more of your rack rolle...
The door spring, used in dishwashers, adds tension to the door through the door hinge to keep it from opening too fast. If you have a door latch failure or your washer door drops too quickly when open...
On a washer, this part is used for circulating the water. On a dishwasher, it is used for draining the water during operation. If you notice your appliance is not draining properly, the circulation pu...
This is a door gasket for a dishwasher. It creates a watertight seal between the dishwasher door and tub to prevent leaking while the appliance is in use. The gasket is approximately 76 inches long an...
This is a pump gasket, also known as a pump housing seal, for a dishwasher. The gasket is fitted around the edge of the pump, preventing leakage between the pump housing and the filter housing. Locate...
This is an accessory assembly, otherwise known as a mounting bracket kit, for a dishwasher. This kit includes two brackets, a hose clamp, and two screws. The brackets are perforated so they can be cut... No Longer Available
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
January 16, 2020
Try to run a load of dishes had run some the night before no problems when i tried to power it up to set it to wash nothing happened. When i jiggled the door something made power come on maybe a loose wire. I start running it a few minutes later it shut down and this time it wouldn’t power back up. When i jiggle the door again thought i saw a little spark at the bottom so i unplugged it and left it.
For model number LDF6920ST
Hi Kent, thank you for your question. It sounds like you may need to replace the door latch/lock: PS3522841. That part will not allow your power to come on if it believes that the door is open in any way. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
January 26, 2020
Just got the error code le while dishwasher was running. Shut off the breaker and restarted the cycle and got the same code. Error code said its either the wiring harness or the motor. It's been much noisier recently so i'm guessing its the motor. Is there any way to tell which it is for sure? Tried to see what a motor would cost and found multiple motors listed. What motor does this code refer to?
For model number LDF6920ST
Hello and thank you for writing.
The LE error code on the LG dishwasher display is an indication of a MOTOR ERROR. The 5 issues that may cause this fault code is a wiring problem (the most common reason for LE error), the impeller of the washing pump is locked, the rotor of the washing motor is locked, the blade is locked, or the PCB main control board is faulty. According to our database, the model number you provided is just a portion of a model number with multiple possible variations. To ensure that we recommend parts that will work for your model, please check your information again; you will need to provide us with the full model and serial numbers located on the sticker on the unit itself.
Once we have that information, we would be happy to find the part you need. We are looking forward to your reply, please always notate the model number. Thank you.
Simple, removed screws securing machine in the cabinet, then pull the unit out of the cabinet space about 10 inches. Springs are accessible within this extension. You need strong hands to extend the springs and attach them. Once attached, push machine back in place and re-install the anchor screws. In my situation, only one spring was broken, so the attached side revealed the correct slot to place the hook on the top position, the bottom position has a plastic lead for the spring, and that lead is attached to a rope to the door hinge. Note: Replace BOTH springs, even if only one is broken.
When I turned the dishwasher over I discovered the PS3579323 diverter motor had failed due to a leak around the PS3536016 valve, check. No use replacing the diverter motor without fixing the leak so I turned the machine back over and disassembled the spray arms and top of the pump cover which reveled the case assy and the valve, check. Upon removal of the valve, check I discovered hair wrapped around it which compromised the MO31 packing and caused the leak. I probably could have just cleaned out the hair and reassembled it but because my installation is a bit of a pain I elected to change the case assy (because of a slight depression where the packing sets) the M031 packing, the MO25 valve, check, and the MO35 pump gasket. After that was accomplished I turned the machine upside down and replaced the MO26 diverter motor and reinstalled the dishwasher. End result: Ne code cleared, no leaks and now the dishes are clean on the top shelf and the wife is happy. There are great instruction videos on YouTube. Good luck!