Parts That Fix KitchenAid Dishwasher KUDS30IVBL3 Door latch failure
Door latch failure is a commonly reported symptom for the KUDS30IVBL3 KitchenAid Dishwasher, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your KUDS30IVBL3 KitchenAid Dishwasher that will fix Door latch failure. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The kit includes two door balance links and two door balance mounts with wheels, which will replace both the left and right sides. The only tool needed is a 5/16 nut driver. Before removing the existing kit, take note of how the door balance link kit is assembled for a smooth replacement process. It is recommended to check the door springs in case they need to be replaced as well.
Replacing your KitchenAid Dishwasher Door Balance Link Kit
Customer Repair Stories
Door spring link broken
2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.
3. Make sure you have enough slack in the water i ... Read more nput line and electrical wiring that you can pull the dishwasher out about 12 inches or more.
4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.
5. Reverse (2 to 1) to reinstall the dishwasher.
-
Sean from Ramona, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench (Adjustable)
Replaced Hinge Link
-
Scott from Fort Lauderdale, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
NOTE: This part is no longer available in white or biscuit. HANDLE only.
Customer Repair Stories
Door handle was sticking in an up position
-
Brian from Charlotte, NC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Door handle broke on the inside of door
-
David from Beloit, WI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
This spring is located in the door section. Sold individually.
Customer Repair Stories
Door release spring
-
Judy from EDWARDSVILLE, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
broken handle
the springs are a bit hard to get on, but once they were in place everything went well. You need 2 people to assemble it.
One to hold the door and the guts of the ele ... Read more ctronics, and the other to install the handle.
-
Lore from Sunland, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
This part releases the detergent and rinse aid into the dishwasher. Light grey in color. The detergent dispenser attaches to the inner door panel and holds the dishwasher detergent and rinse agent in a covered compartment.
Replacing your KitchenAid Dishwasher Detergent Dispenser Assembly
Customer Repair Stories
Plastic catch that releases the soap dispenser door broke off, the soap dispenser door wouldnt stay shut.
-
Patrick from Byron Center, MI
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
latch on dispenser cover broke
-
Craig from Austin, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set
Handle is not included with this part.
Replacing your Kenmore Dishwasher Door Latch Bracket Kit - NO Handle
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward. The bracket is made entirely of metal. It is recommended to check all brackets, if applicable, because they often wear at the same rate and both may need to be replaced. This is an OEM part that is sourced from the authentic manufacturer. Tools needed are a pair of needle nose pliers and a screwdriver.
Replacing your KitchenAid Dishwasher Mounting Bracket
Customer Repair Stories
Broken Mounting bracket
-
Roy from HIGGINSVILLE, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Lost dishwasher brackets
-
Judith from Essex, MA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
This part is the door actuator for your dishwasher. It is made of black plastic and is approximately 3 inches long and 3 inches wide at its widest point. The door actuator is found in the control panel, and it releases the door latch when you lift the handle. If your current door actuator is cracked or broken, you may not be able to open your dishwasher door, or the door will not close properly. The dishwasher also may not be able to start, and if this is the case, you will need to replace it. This part is sold individually and is an authentic OEM part.
Replacing your Kenmore Dishwasher Door Actuator
Customer Repair Stories
Latch broke
-
Don from St. Joseph, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
This dishwasher door spring is sold individually. It is recommended if you are replacing one side, to replace both.
Replacing your KitchenAid Dishwasher Door Spring
Customer Repair Stories
Door spring broke-Door falls down
-
Peter from JERICHO, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set, Wrench (Adjustable)
The Door Just Falls Down
-
Neil from Winchester, VA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
This dishwasher door switch will shut your dishwasher off when the door is opened.
Replacing your Kenmore Dishwasher Door Switch
Customer Repair Stories
No power to dishwasher. Quit mid-cycle.
-
Jon from Bend, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Would not start
-
James from Norwich, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack stop may need to be replaced. The replacement part may differ slightly from the broken part, depending on the model. However, the different styles are interchangeable. This product is sold individually and comes in both a white and grey plastic version. Many of our customers found this repair to be very easy and takes less than 30 minutes to complete. Simply snap the old part out and snap the new part into place. You will not require any tools to complete the job. This is an authentic part approved by the manufacturer.
Replacing your Whirlpool Dishwasher Rack Track Stop
Customer Repair Stories
Roller wheel broke off upper rack and also end rack stops needed replacing.
-
Carole from IRVINE, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
Lost stop from one side of top rack. Rack could be pulled off track.
-
Sheila from FAYETTEVILLE, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
Serves as a mechanical actuator for door switch operation and provides door tension for proper seal.