KUDS01FLSS1 KitchenAid Dishwasher - Instructions

After replacing the door latch which was not faulty I learned fron a local appliance repair company the door was distorted as a result of an earlier failure of the cable assembly breaking. The door opened with such great force hiting my leg and apparently distorted the door or machine frame. The fix was to bundle a towel and place it between the door and dishwasher sides, one at a time, and forcing the door in a closing direction to bend the door and frame. After several attempts the door now closes well and remains shut during the cycle.

Disconnect the water supply, the drain line, and the two screws that go up into the cabinet frame, then pull the dishwasher out from under the counter. Tip the unit onto it's face and the main pump/motor is facing up. Turn off the power then unplug the electrical connector from the motor. Remove the single bolt at the base of the motor then turn the whole motor ~1/4 turn counter-clockwise. A firm pull will remove the motor/pump at this point.
The new motor/pump has a new seal. See that the arrows on the pump volute and the motor frame are lined up before inserting into the housing. The new motor/pump slides into the housing easily and a 1/4 turn clockwise will pull it in tight. Re-install the locking bolt and revers the rest of the steps to get running again.

Unplug the dishwasher. Remove the screws holding the stainless lining to the outer door panel. Unplug the various connections. remove the control panel by pushing small plastic cleats outward (they are spring loaded). Remove the printed circuit board by pushing one holding tab to realase then tilting the board out. Remove the ribbon cable by sliding it off the circuit board. Now reverse the process. Attach the ribbon cable to new circuit board, snap in the circuit board to the control panel (ribbon behind), reattach all electrical connectors, reassemble the door "sandwich". Somewhere in there you also need to remove then snap back the door lock assembly. This is a simple repair with no fancy connectors or tools. Repair service wanted $400 plus two service calls (one to diagnose, one to install). My total about $120. I am a klutz re: repairs.

Actually, the repair was very simple because of the you tube video demonstrating the repair. This made the repair very easy. I repair/replaced both springs and links

When the dishwasher is pulled out from the cabinet the nuts that hold the element in place are readily accessible. Pull wires off spade terminals, unscrew nuts, remove and replace element. I tightened the (plastic) nuts 3/4 to 1 turn, and used a little silicone gasket maker on the rubber gaskets provided with the new element.
The electronic module is easily replaced by removing the upper part of the dorr panel (top 6 screws). Transfer the wires to it and snap it in place of the old one. This Whirlpool repair set fit perfectly in this Sears dishwasher, and works as it should.

Very simple. We had to remove the screws holding the metal cover on the inside of the dishwasher to access the electrical panel. Then we disconnected the wires that were connected to the fuse kit, unclipped the kit from the panel, clipped the new one on, and replaced the wires. Then all we had to do was screw the metal cover back onto the inside of the door and it worked just fine.

I removed the screws around iner door panel. this allowed me acess to the hex head screws holding the plastic
air inlet and replaced it. the small tabs on the ends of the old inlet had bent
up allowing the water to flow by

.The easiest way to complete the impeller and chopper motor replacement is to disconnect the power, water and drain line, remove the dishwasher from the cabinet, set the washer on its back.

From this point everything is visible, pump housing, motor, etc. and it's a matter of disassembly and reassembly. Make note or a drawing of where all the wires are connected so you reconnect them in the right spots.

Reinstall water lines and power and check for leaks before replacing shield or kick plate.

First removed bottom kick plate cover to reveal the Inlet valve. Saw that it was leaking around the plastic around the solenoid. Turned of the water shutoff valve and unplugged the power cord. Unplugged the two wires from the valve and loosened and removed the tubing going into the valve. Removed two screws that hold the valve assembly to the front frame with a nutdriver. Slide assembly to the right and remove from the two slots. Ordered new valve from Partselect and replaced.

If your chopper assembly has a catastrophic failure like mine did, chances are it took out the teeth on the circulation motor as well. This will lead to the teeth on the chopper being destroyed by the impeller as soon as you turn the dishwasher back on. First, follow the instructional video to remove the motor (found on this site on the circulation motor page) and chopper assembly (also found on this site on the chopper assembly page). The impeller is screwed onto the input shaft of the motor, and you must keep it from turning so that you can unscrew the impeller assembly. I removed the back cover of the motor (there are four screws holding it on) and held a flat pry bar on the rotating assembly inside the motor to keep it from turning, then unscrewed the impeller from the shaft. Mine came off very easy, but be careful not to let your pry bar slip or damage the motors internals. After that, install the washer and grommet from the impeller seal kit on to the impeller, and screw it back on while keeping the motor from turning with your pry bar. Lastly, reinstall the motor and chopper assembly per the aforementioned instructional videos. The whole thing took around an hour to do, and it is much cheaper than replacing the entire circulation motor.

First changed motherboard and door switch, which didn't fix the problem. Inspected door latch and saw that one of the tabs was broken. Replaced latch and problem solved.

I followed the YouTube video exactly and it went very well

Popped the old housing apart with screw driver, saving internal part, installed part into new housing, placed in posistion, installed two new screws and it worked like charmed. So simple, I have ordered 2nd part to replace opposite side which is not yet broken. Thanks to the terrific phone assistant who convinced me it would work and not have to replace the entire rack which was suggested by a repair man. . . . . . Many thanks! ! ! !

I simply pulled the top rack out as far as it would go, reached in and gently bent supply arm down so I could get the snap button (male end) in from the top. The female end and the wash arm then just snapped up into the male end. It took less than a minute. I probably saved about $75 doing this myself.

Replaced the pump drain as one complete assembly. Couldn't do it from under the front panel as there is a small lug that you have to depress on the top of the assembly before you can twist the assembly counter-clockwise by hand. I tried but I couln't get the leverage. Had to take dishwasher out from under the unit and tip it on its side. The rest was very straightforward. If you can remove the dishwasher from under the unit easily I would suggest you don't even bother trying to change the pump drain while the dishwasher is in place. It's not worth the hassle.