KSB5WH4 KitchenAid Blender - Instructions

I first tried to do the repair just like the directions ,trying to force off the wheel. Then I tried doing it the way the readers here did with a tthin pliers and was not sucessfull. I then took it to a hardware store and ask about a certain pliers,they did not have it. The older man at the register took two screwdrivers from the jar next to him took my blender and pried on either side and popped off the wheel just like the original directions said. It was then easy to put the new one on.

I unscrewed the old coupling and screwed on the new coupling from Partselect.
This was a personal repair job.
However, I am a local Handyman in Northern NJ that does a ton of minor repairs. For all of my appliance part needs I will buy from Partselect.com. They under promised and over delivered! Just incase you dont know what I mean by that statement,,, I ordered the blender part, they told me I would have it in 6-10 days (which was acceptable to me) and I had it in two days... AWESOME job FOLKS!!!!!!!

After reading repair stories on this site, I used wire splicers that just fit between the coupling and housing to hold the shaft while I used pliers to remove the broken coupling. I then hand tightened the new one . It works fine now.

Thanks to everyone before me and their stories!
I felt confident enough to try repairing my blender myself ! ! !
I just placed a flat head screw driver under the coupler and pushed up on the screw driver, 3 or 4 more times around the coupler. It broke away and a metal disc was left, which I unscrewed and I just screwed the new coupler on.
Thanks Again!

Followed the directions and used a screwdriver to pry off the old gear. Screwed the new one on - reverse thread. Easy as that.

used thin wire strippers to hold screw shat, than unscrewed one and screwed on the other. done

Popped off the old one and popped on the new one. It took no more then 30 seconds and the blender is like new again.

I inserted a metal rod in the bottom of the base while I held it sideways to keep the motor from turning and I used pliers to twist the coupling off counterclockwise.
I thought at first I was doing it wrong because it wouldn't nudge so I left it alone. I then read the repair stories again and went back to it and it right came off. I guess there was a lot of gunk holding it tight.
Of course when the new one came days later it was easy to twist it on. Thank you for all of your stories. They were very informative and encouraging. Without them I'm not sure if I would have attempted it myself.

i used the screwdriver method prying up on side to side old one comes off new one goes on pretty cool also it was a nice long flat head with pretty big head

It was very easy to unscrew the coupler I used locktight to put on the new part. Thank you sending
the right part the first time
Albert

Released cup drive with screw driver and un-screwed, screwed on new driver.
That is all, works like a new blender.

simply hold the axel with the wire stripper to prevent from rotating. Using the pliers firmly turn old coupling counterclockwise until loose. Once this coupling is totally off you are ready to screw on the new one. Very simple. The most difficult part was finding a tool slim enough to fit between old coupling and base to hold axel from spinning. I ordered part on sunday and received it on tuesday. It spared me from throwing away a $120.00 dollar kitchenaide blender.

it was too easy, i only used my hand to screw the coupling to the blender.

Using the precise instructions provided by parts select, I used a big screw driver and pried off the old coupler and cleaned the area and screwed on the new coupler. Fixed!

The part finally arrived 3 weeks later, after being out of stock and back ordered a couple times.

The coupling split apart on my Kitchenaid Blender. I ordered the coupling part and "Bingo", I was back in business. It took no time at all and one screwdriver. I saved penty of money by not having to buy a new appliance.