Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Refigerator door was not closing all the way if not pushed shut.
Remove the top hinge cover. Removed the top hinge support. Lifted the door from the bottom support. Old door cams were worn completly flat. Replaced the lower door cam and closing cam use a little vasalene for lubricant on the cam surfaces. Placed the door back on the lower hinge support. Replaced the top hinge support. Door is closing great now. Thanks for the quick part deliver.
Seven year old condenser fan was making noise when it was running.
The process to repair was very simple, I removed the back of the refrigerator to expose the motor area. I then removed three screws that held the condenser motor in place. once it was loose I detactched the electrical harness and removed the old motor. I then placed the new motor in place and secured it with the screws and reattached the new electrical harness that came with the new part. Once completed I reviewed it to make sure I didn't miss anything. I then replaced the cover over the motor area and enjoyed my success in repairing my own appliance with no added cost for labor, which would have been expensive I'm sure. The part purchased came with clear and consice instructions very easy to follow.
1. 1/4 drive socket and standard socket 2. On top of door .... remove black plastic bracket cover on top of hinge 3. Have someone hold the frige door in place 4. On top of door .... remove 3 screws that hold the hinge onto the frige..... at this time, door will be loose 5. Lift door up and off the bottom hinge. 6. sit door on the ground. Tilt door at an angle for access to the "cam" 7. On frige, at the bottom, use socket to remove one screw that holds the old "bottom" cam in place..... then replace with new one. 8. While door is tilted, use socket to remove one screw that holds the "top" cam in place. 9. You will need to gently pull this cam out.... shouldn't take too much effort though. 10. Replace with new cam. 11. put door back on hinge 12. At top of frige, reinstall 3 screws 13. Reinstall plastic cover. 14. Voila, you're done
Fridge was warm. No air circulating at all. Food was spoiling Fridge was just over 1 year old
First I removed the two screws that secure the guard in bottom back of the freezer and removed it . Next I removed the two screws that secure the guard on the back wall of the freezer and removed it. There are three wires connected to the motor, I unplugged those and removed the two screws that secure the motor and removed it. I swapped the grommets, blade and support bracket from the old motor. I put it back together in reverse steps and its working great. My mother-in-law can,t stop thanking me ! I saved her at least $400 to buy a new fridge. Thank You, Brian Miner
We have a side-by-side fridge/freezer and we experienced a hot center post (where doors come together) and the fridge made loud noise. Also, the (old) fan motor would start, but then quit, so our issue was the motor.
For me the repair was very easy, but for an unexperienced person it may prove to be difficult. If you must order a motor/fan, do NOT order the metal fan as a plastic fan comes with the motor. What's strange is the new motor is different than the old one, but it still mounted without any required modifications. I did NOT use the wire harness that came with the motor either as it was different too, but my old one was still good.
Check all of your parts as my fan had a cracked blade, but I used "superglue" and it's fine now.
Fridge stays cold and my wife had to lower the temperature in the fridge as she was blasted by the cold!
The door is very easy to remove. There is one nut for the cap on the top of the soor hinge. Once the cap is removed, you need to remove the 3 nuts holding the hinge in place. Simply lift the door off the lower hinge and rest it on the dining room table. I set towels down to protect the stainless finish. The closing cam will be visible on the bottom of the door. I choose to replace the lower cam and the upper cam at the same time. I did not know what the problem cam was. The door works good as new. I put a small amount of vaseline where the two cams rub to provide a lubricant.
old condenser fan motor shaft was loose and it made the spinning fan blades shake and cause noise
The procedure was straightforward. I removed the cardboard backing on the lower back of the refrigerator to expose the fan unit. I then undid the electrical harness at the fan. I then removed the three screws securing the fan motor to the metal bracket. This is the hardest part in that I had to reach through and get to the screws with my small tools. I then removed the old motor and blades and placed the new motor and blades. Again, a bit tricky trying to get the three screws mounted into the bracket...small tools and hands helps. After that I used the electrical harness supplied with the kit to plug into the new motor and I was done.
Replaced the door cam on bottom of fridge door. ONE THING TO UNDERSTAND- THERE ARE 2 CAMS ON THE DOOR, LOWER AND UPPER, BUT THE UPPER CAM IS NOT LISTED ON THE "DOOR HARDWARE" DRAWING, ITS LISTED ON THE MAIN BODY DRAWING! BE SURE TO GET BOTH CAMS! (PARTSELECT COULD MAKE A NOTE THAT WHEN PEOPLE LOOK UP LOWER CAM, PUT A NOTE IN THERE SAYING Y0U NEED UPPER TOO!)So I had to order the upper cam later and install later. BUT it is quite easy to replace, unlike the video, I only needed 1 tool! The nut driver (electric screwdriver w nut driver head). Thanks -RF
Frige Door Wouldn't Stay Closed, Would open when freezer door was closed.
Parts arrived at 2:30PM.
Read instructions, gathered tools, and went to work. I'd already watched an online video at your site on how to do the repair.
Removed the hinge cover covering the hinge top by using a nut driver to remove the single screw holding it in place. (The video described an older frige and it did not have a screw. I figured that out when I finally went and got a ladder. I had tried to pop it out like the video shows.) There are three screws holding the hinge top in place. I tried using the nut driver to remove the screws but they were pretty firmly in place. I resorted to using my ratchet wrench and that made it easy. (Keep track of your screws, one of mine rolled under a cereal box on top of the frige and I thought I would never find it.)
I had emptied out all the items on the door of the frige, removing the shelves. It was easy to lift the door off of the bottom hinge and lay it on its side against the ladder. At this point I had my son hold the door steady (its kind of unwieldy and 'slippery' when you are trying to remove a screw from the bottom of the door.)
I removed the screw that held the plastic Door Closer, Upper Cam using the nut driver. I used a straight bladed screw driver to pry the old part out of the door (it has an insert for the hinge pin and it had been in place a long time). I also cleaned off the bottom of the frige door (you would be surprised what gets stuck on there - obviously someone spilled oranged juice on the floor and it splashed up on the bottom of the door). The old part had a lot of particle dust that came off it when I removed it. The new part popped right into place and I screwed it back in. The video shows that the repairman had to use a drill and tap set to rethread a larger hole but I just put the old screw back and it held fine. The video also showed the repairman adjusting the Door Stop Bracket but I didn't have to do that, the new cam installation wasn't impeded by the bracket.
I moved to the frige cabinet (again, good to have a second pair of hands to keep track of the door and not let it get damaged while I turned my attention to the Door Closer, Lower Cam. I used the nut driver to remove the screw holdin it to the hinge bottom. It came off easily (it practically fell apart and turned to dust). I placed the new cam and screwed it in using the old screw. No problem.
You could put the door back on with one person but it helps to have two. One to manhandle the door and the other to place it on the lower hinge post.
I put the upper hinge back on and put in the three screws but I left them lose so that I could adjust the door. When I tighted the single screw closest to the door after positioning the door, we tested how it opened and it was hitting the side of the interior cabinet when it closed - you could feel it dragging and it made a clunk/swoosh sound. We readjusted the door using the outside upper corner as a guide and retightened the screw. This time there was no problem. We tighted the other two screws using the ratchet wrench and then put the plastic hinge cover back on with the single screw using the nut driver.
Took us about 25 minutes and made my wife very happy (biggest benefit). The door now 'locks' open and 'locks' closed just like when we bought it and the two doors are aligned (level accross the top) which should have been a dead giveaway that the door closing cams had worn down.
Very pleased with the delivery time. Was able to repair the refrigerator before the beer got hot. Replacement was easy. Removed blower housing. Replaced motor. Put blower housing back in place.
Refrigerator door fails to close on its own like it is designed to.
The design of this refrigerator door (it's a side-by-side) is somewhat unbelievable. The door is designed to hold things, yet when you do the weight of the door wears out the lower door cams. The cams are designed to "complete the door closing", i.e. when you gently push on the door the cam mechanism takes over. When the cams wear, the door fails to close. Note to others - you may mistakenly think that the failure of the door to close is related to the seal; it is not.
The repair is quite easy; remove the upper cover, using a not driver (socket), then remove the upper door bracket. Make sure you hold the door or have someone else hold it. After the fasteners are removed gently lift up on the door and remove it from the lower cam assembly. You will see two plastic cam pieces; one on the lower bracket and one on the door. Both need to be changed to effectively "renew" the door closing mechanism. Once the cams are replaced the door can be reassembled to the refrigerator.
removed the clip that the motor was attached too put the new motor back on reinstalled the clip back on the fridge plugged the wire harness in and works perfect now . it was easier to remove the clip than to try to install the motor by itself its just to tight and you cant get in there
Unplugged the machine removed the bottom plate and back plate and ice maker.Removed 2 wires to motor and ground wire.Removed 2 mounting nuts for motor,installed new motor and used old fan blade for new motor .Reinstalled in reverse order plugged in and tested fine.
I removed the screws on the upper hinge and removed the door. I removed the lower cam in about 2 minutes and had it replaced. The upper cam was a tight fit in the door and I resorted to vise-grips to remove it. Total time to replace cams and put the door back on was 30 minutes. This saved me $100. Thanks
I removed 4 screws holding the motor mounting bracket and removed the assy from the unit. I then removed 3 screws holding the motor to the bracket. I put the fan blade on the new motor and reattached the motor to the bracket. I plugged in the wiring adapter to the motor and reinstalled the bracket in the unit with the 4 screws. Finally I attached the unit wiring connector to the motor. It was relatively easy.
