Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KGU5955BS

KGU5955BS Maytag Refrigerator - Overview

Get Parts and Repair Help for KGU5955BS

If you know the refrigerator repair part you need, you can browse the list of all parts on the KGU5955BS, or you can search by name or part description. You can also find your part by where it is located on the KGU5955BS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for KGU5955BS parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$96.00

Replacement Ice Maker

This is a replacement ice maker. This assembly includes the ice mold and the control device. The water inlet valve pumps water into the mold, which stays there until it is frozen s...

$11.11

Light Rocker Switch

This light rocker light switch is used in a number of household appliances. It is most often found in refrigerators and freezers. This is a simple mechanism that helps turn the light in your appliance on and off. If the door of your appliance is open the light should be on, and if the door is closed the light should be off. Your appliance door is opened and closed frequently, meaning the mechanism may wear out over time. It is not uncommon that this part will need to be replaced. You may need a putty knife to release the mounting tab and remove the faulty rocker switch. To install the new one, simply attach the wires and snap it into place in the liner of your refrigerator or freezer.

$2.96

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this sc...

$37.73

Condenser Fan Motor Kit

This condenser fan motor kit is designed for use with refrigerators. This fan draws air through the condenser coils and over the compressor. It does this with the goal of cooling the warm refrigerant before it enters the evaporator. When your fan or fan motor is not working your refrigerator will not cool properly. This is a 2-Watt, 115 Volt motor that rotates the fan in a counter clockwise direction. This kit includes the hardware needed for installation, and a set of instructions. Before you begin any repair work make sure to unplug your appliance.

$5.40

Screw

Sold individually.

$4.88

Screw

Sold individually.

$32.80

Single Outlet Water Valve

The single outlet water valve may also be known as the water inlet valve and is compatible with your refrigerator. This valve has a quarter-inch tubing inlet connection. When energ...

$5.27

Lower Hinge Pin

This is a lower hinge pin for your refrigerator door. This hinge helps your door open and close easily by allowing it to pivot. You will need to replace your lower hinge pin if your refrigerator door will not open or close properly. This part is almost two inches high, one inch wide, and roughly two inches long. You will need a Phillips screwdriver and a 5/16 nut driver to replace this pin. It is made entirely of plastic and is all black.

$24.22

BLADE-FAN

The fan blade is used to blow air over the condenser.

$2.96

Screw

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray

  • Customer: Bernie from Diamond Bar, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 741 of 789 people found this instruction helpful
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of con... read more

Water overflowed ice maker turnning ice bucket into solid mass of ice

  • Customer: Harry from Grand Ledge, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 256 of 332 people found this instruction helpful
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: o... read more

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 141 of 153 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more