KEYL410BAL2 KitchenAid Dryer - Instructions

Everything seems to work on the electric/gas dryer, but would not generate any heat. Did some research and ordered the thermal fuse & thermostat based on that. Replacement was simple and went well, however it did not fix the issue. Should have checked the continuity first as I found the "replaced parts" to be good. Have checked all other possible symptoms except the heating element, which requires addition labor. Overall, partselect portion was as advertised. All parts arrived quickly and were priced fair.

After tearing the back off by removing the numerous 1/4 inch hex screws, and locating the schematic in the compartment behind the dryer controls, I took a multimeter on the resistance setting and tested all the components I deduced were part of the heating circuit until i found the upper limit temp fuse of was open (i.e infinite , OL, how ever your meter will display this). I ordered the kit from here and upon installation found I had a different type of Thermistat assembly then the kit came with, however, the kit did anticipate this might happen and had "some" instruction on modifying the wire harness to accommodate the part. Essentially if you have this older style you will need to do some basic wire stripping and crimping to make it all work. While I am an electrical technician on aircraft, anyone should be able to follow the how-to video on this page(which deals exactly with what I had) and with the proper tools install this part.
I also cleaned out and inspected the rest of the dryer since I had it all open, including looking for burning on the heating element and inspection of the rest of the wiring harness. Finally removed the lint chute by removing the two screws located under the lint basket door, and the nuts holding it to the dryer frame and did a work over on it, finding a lot of compacted lint and debris inside. A can of compressed air helped a lot for this.

I deduced the lid switch was the problem.

I removed the two screws holding the control panel on. Pulled the control panel back.
Disconnected the ground wire of the lid switch.
removed the two top clamps that hold the panel to the top of the machine.
Pulled back the casing (outside of the washer) and placed it on it's side on the floor. Here I could reach the switch. Removed old, installed new and reversed the process.

The part that gave me the biggest problem was setting the casing back on to the frame. You have to slide the front part in at the bottome, then lean back the rest of it.

If you were to do the Belt Replacement only, here is the quick synopsis:
1. Unplug dryer;
2a. Open lint door on top of dryer and remove the two phillips head screws that hold the lint bay to the metal dryer top;
2b. Next remove the two brakets holding the metal top to the dryer back (one screw on each bracket);
3. Use a flat-blade screw driver to pry off the top of the dryer (leaving the timer and start button area attached);
4. Lift off top and push back to expose just enough area so you can get to the two screws holding the dryer sides to the dryer front;
5. Unplug door switch;
6. Unscrew screws from #4;
7. With door open, lift dryer front (only about an inch) and then pry bottom of dryer front from dryer sides. The bottom of the dryer front is not screwed, just siting on Front Panel Clips;
8. Once the front is off the dryer, simply remove the belt and install the new one. Please note that while you are in here, you may want to inspect the rear drum seal and replace if it is worn to the point where metal is rubbing on metal. This is also a good time to clean out dust from inside this cavity to help extend the life of the bearings on the rollers and prevent dust from accumulating and gunking up the motor, etc.
9. Re-assemble tin the opposite order.
If you have any mechanical sense at all and you don't know anything about dryers, you will be surprised at the simplicity of the dryer.

The dryer wouldn’t turn on at all. It was like it was unplugged from the wall. However, fixing it couldn't be easier. I simply removed the back panel, found the fuse, tested it with an Ohmmeter (to determine that this was the part that didn't work), ordered the part from this website, and replaced the part. The part arrived in about two days. The shipping was a little pricey, but overall the whole thing cost me $20 vs. whatever it would cost me to get someone else to repair it. The website helps to identify the problem, and it is helpful to read how other people fixed their problems. It was so easy and the service was so good, I will definitely use this website again and recommend it to others.

The dryer motor quit working. Learned, if you are changing one that is old, get the blower wheel fan too! I could not break mine loose from the motor shaft, and had to bust it off.

To un-screw the blower wheel fan from the motor shaft: from the front of the dryer, grab the plastic fan on the back of the motor with an adjustable wrench, and the motor shaft on the front of the motor with vice grips. Turn the motor shaft CLOCKWISE holding the fan still to un-screw the fan. If you have to remove the pulley, grab the shaft and turn the pulley COUNTERCLOCKWISE with a wrench.

Just make sure to pay attention to the orientation of the new motor in the instructions. If you match the old motor, it will not fit. It is all spelled out in the directions.

First I removed the two wires from the overheat fuse, then I removed the 1 screw and removed the fuse. I installed the new overheat fuse and attached with 1 screw, then reconnected the 2 wires. I attached the back cover with two screws and tested the dryer. It was working, so I finished attaching the back with the remaining screws and exhaust duct. Installation complete.
Note: Two weeks later I had to replace the fuse again because I had checked the duct pipe and exhaust chute, but not the bottom at the fan. Be sure to remove the flat exhaust duct and check for bulid-up at the bottom under the fan.

pulled out filter measured it looked on internet found this site ordered it threedays later BINGO new filter thank you!

the job would have gone faster if the right parts had been sent in the first place. I would have never paid for two day shipping. In the repair, I removed the rear panel, clipped the plastic triangle holding the bearing, installed the new bearing and new clip.

First and most important was to unplug the unit.
I removed the 2 screws that hold the lint screen shoot to the top cover and then simply popped the top of the machine open using 2 screw drivers and
gently prying it up. I raised the top cover about 8 inches and supported it with a block of wood.
I opened the front loading door and removed the 2 screws that hold the door actuator switch while holding the switch on the inside so that nothing would fall down into no mans land. Once the switch was loose I pulled it into view and could see that the actuator spring was broken. I used the search at the Part Select Web site and found the placement part very easy. I was amazed that the part was shipped and delivered to my house the very next day. The actuator spring simply snaps into place and I assembled it in the reverse order of removal, I removed the block of wood and snapped the top back into location and reinstalled the 2 screws for the lint screen shoot . I plugged the dryer in and it work perfect. I can't say enough about how well the experiance with Parts Select went, I will recommend them to others.

First I unplugged the dryer for safety, then I removed the top of the dryer, then removed the 2 hex head screws holding the font door panel onto the dryer. Then I disconnected the door safety switch. the rest was cake. I removed the old bearing and cut the new bearing and seal to the exact size of the old one. I used contact cement to glue the new bearing and seal into place. Reassembly was a breeze. End of job. Success!!!

Got a new one

My daughter found the video on youtube, which showed step by step repairing procedures. I just followed it and fixed my dryer in 15 min.

Purchased thermal cut off kit but only replaced the top most thermostat. There were some extra wires wired into the bottom thermostat, that were not described on the video or any other repair user posts. It checked fine on my multimeter anyway.

I ordered the switch, which is what most people told me the problem was. I didn't have a multimeter, so I couldn't test the current one.

I removed the two screws from above the lid switch, removed the control panel screws on either side, and used a flat screwdriver to pry the top off by popping the clips.

The switch was easy to reach, and I compared the old and new switch after removing the paddle assembly. The new switch has three prongs, whereas my old one had two, so I put the gray wire terminal onto the bottom prong. I set everything down, plugged it in, and tested it, but still no spin cycle.

After some further research, I realized the problem was with the spin solenoid under the washer, or the red wire that leaves the lid switch and goes to the spin solenoid, also called a wig-wag solenoid. (This is a belt driven model, not direct drive.) It's not too common that the solenoids fail, but it is rather common that the wires break inside the insulation on this model.

Moral of the story is always ohm through the switches and wires before ordering replacement parts. (Remember, never ohm through a live circuit.)