KDRP487MSS03 KitchenAid Range - Instructions

Removed old fan by removing all screws except the back two lower screws - here I cut the flange on the old fan to remove. Drilled the back two bottom holes so as to fit over existing screws then replaced the top 3 and bottom 2 screws as well as power leads. Offset screwdriver is a must.

Installed a new thermostat and noticed the convection heating element wire had burned in two. Ordered new element and installed. Oven is currently working properly again.

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

First of all I would like to say how prompt the delivery of my oven glass was. I ordered it Thurs & it came on Sat ~ 2 days thats amazing! Ordering my glass was easy & the representitive that helped me was very nice & the price was great! My husband repaired it in about 20 minutes - very easy to istall the glass & very cost effective repairing it ourselves rather than having a repair man come out! Thanks Part Select I will recommend you to all out fam & friends most definetly!

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

Repair was super simple . Any one could have done it.

turned breaker switch off. unscrewed the oven from the cabinet. lifted the oven out of the cabinet (heavy & awkward, needed an extra pair of hands). removed back panel. replaced fuse. reassembled everything. this is the second time i've had to replace the thermo fuse (oven blows the fuse when set to clean). first time i replaced the fuse it took about two hours. second time it about an hour.

followed the brief instuctions you provided easy as pie

Had to screw off old terminal block & screw on new one

Not difficult, but there are several layers of glass, metal, and insulation inside this door. Keep track of where the screws go and have room to lay out all the layers. You'll reach the cracked inner glass last.

pull out the stove,took the top back panel off, take off wires one at a time on new spark module.. easy

I turned off the power from the circuit breaker. I then removed the doors and the trim package from around the oven. I slid out the oven and had my husband help me lower it to the floor. I removed the back covering and then removed the wires connected to the old thermostat. I unscrewed the old thermostat and replaced it with the new thermostat. Did everything in reverse and it seems to be working very well. It took about 30 minutes total. Some sites suggested that a fuse needed to be adjusted/replaced. In this kitchen-aid double oven and I'm assuming whirlpools as well, the thermostat/fuse is one piece located on the back of the unit. It was very simple. The piece cost $47. Such a great investment of time and money. I had the piece in 2 days, without paying extra postage.

A generic video on Youtube was actually very helpful as it showed how to remove the door from the oven for easier glass replacement. The only tricky part is getting the panes of glass in the correct order during reassembly,as there are actually 4 pieces in the door. Only the piece that faces the oven's interior was cracked on mine. The two inner pieces between the two outermost pieces are the ones not to mix up. This little repair also gave me the opportunity to thoroughly clean all 4 pieces of glass that had become rather dirty over 12 years. Now the oven door looks like new!

Removed with screw driver the gasket clamp at bottom of door opening and then pulled away the old gasket. Installed new gasket making sure that each holding pin was insert in mounting holes, trimmed away un-raveled gasket material at ends and reinstalled gasket clamp at bottom of door. Removed old oven racks and installed new racks.

Removed wall oven from wall. Removed back cover. Unscrewed thermastat and removed old thermastat. Screwed in new thermastat and put back together.