Models
>
JRT153LH
JRT153LH (7C51B) Jenn-Air Refrigerator - Overview
Sections of the JRT153LH
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.79
In Stock
Door Shelf Trim Retainer
PartSelect #: PS11743360
Manufacturer #: WP65245-1
This door shelf trim retainer is just over one inch long. It is all white in color and it is made entirely of plastic.
$11.72
In Stock
Hinge Pin Bushing
PartSelect #: PS2064817
Manufacturer #: 66036-1
This bushing is used with a 1/4-inch pin. This part is found in refrigerators (and sometimes freezers). The bushing provides a bearing surface for the hinge pin that rotates. Every time you are openin...
No Longer Available
Food Door Gasket (measures 28-1/4" by 36-5/8")
PartSelect #: PS11743833
Manufacturer #: WP70048-1
This white fresh food door gasket measures approximately 28-1/4 inches by 36-5/8 inches. It is used on many fresh food doors of top mount model efrigerators that have been manufactured since 1980.
$60.00
In Stock
Door Shelf Retainer Bar - Cut to Fit
PartSelect #: PS11743151
Manufacturer #: WP61003045
This cut-to-fit refrigerator door shelf retainer bar comes at twenty-seven inches long. It is made entirely of metal.
$83.45
In Stock
Door Hinge Washer
PartSelect #: PS2049932
Manufacturer #: 54233-1
This door hinge washer is used between the lower hinge pin and the lower hinge bushing.
No Longer Available
Washer
PartSelect #: PS11742796
Manufacturer #: WP52185-1
This door hinge washer is less than an inch in diameter. It is all white in color and it is made entirely of plastic.
$7.14
In Stock
BUSHING- L
PartSelect #: PS2064814
Manufacturer #: 66034-1
The bushing is made of white plastic and is for a 3/8-inch pin. This bushing is part of your refrigerator assembly and is found on the top of the door. A worn-out bushing will cause your door to becom...
$22.45
Special Order
Questions And Answers for JRT153LH
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old gasket was ripped, damaged
1. Remove food from door
2. Remove bottom hinge from door. Make sure door is supported. Shoulder works nicely for that. 3 hex head screws
3. Drop door down and off. Lay on table.
4. Remove inside door panel. The hex head screws require a 1/4" socket, and there are a lot of them, concealed under a flap of the gasket. L ... Read more ift off and clean inside door panel.
5. The old gasket peels off. The new one goes on the same way. Place the inside door panel back on the door, and install the screws at the corners first. Make sure that they go thru the holes in the gasket.
6. Lift the door into position. Install the hinge, holding the door. Once it is tight, you are done.
2. Remove bottom hinge from door. Make sure door is supported. Shoulder works nicely for that. 3 hex head screws
3. Drop door down and off. Lay on table.
4. Remove inside door panel. The hex head screws require a 1/4" socket, and there are a lot of them, concealed under a flap of the gasket. L ... Read more ift off and clean inside door panel.
5. The old gasket peels off. The new one goes on the same way. Place the inside door panel back on the door, and install the screws at the corners first. Make sure that they go thru the holes in the gasket.
6. Lift the door into position. Install the hinge, holding the door. Once it is tight, you are done.
Read less
Parts Used:
-
Gilbert from Water View, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
10 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pantry Drawer Cover keeps falling off, not held in place by End Cap Kit
I removed the 2 crisper drawers and the glass shelf directly above the Pantry Drawer. Removed the Pantry Drawer and Pantry Drawer cover so you have easy access to the Right-Hand End Cap. On the right-hand End Cap, there are 2 screws which hold the End Cap in place, use a 1/4 inch driver to unscrew the screws from the front of the cabine
... Read more
t on the End Cap and half-way in of the cabinet, leave the screws in their holes in the End Cap. Lift gently to get off a small plastic pin, and move the End Cap away from the Cabinet. You don't need to completely pull the End Cap out of the cabinet, it'll move more like a door opening. Place 2 washers on each screw and gently put the End Cap back into place, being careful NOT to jostle too much so the washers don't fall off the screws. You will need to gently lift the End Cap back in to place over the plastic pin. Hand-tighten the screws back into place with the 1/4 in driver. Remount the Pantry Drawer on the sliders. When you go to install the Pantry Drawer Cover, you will need to gently push on one of the pins to get the cover back into place. Put glass and crisper drawers back into place.
Test by gently pulling on the Pantry Drawer. If properly mounted, the pins will extend fully into the Cover and will keep it secure when opening the Pantry Drawer.
Test by gently pulling on the Pantry Drawer. If properly mounted, the pins will extend fully into the Cover and will keep it secure when opening the Pantry Drawer.
Read less
Parts Used:
-
Gerald from TANEYTOWN, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hinge missing from acquired refrigerator
We got a refrigerator at a yard sale for free. The door was off and much of it disassembled. When we put it together we realized the top hinge was missing. We asked the previous owner and they didn't have it. We found it with your wonderful web site which so wonderfully detailed the parts.
It was a breeze to put it together and ... Read more we got a refrigerator for about $30.
It was a breeze to put it together and ... Read more we got a refrigerator for about $30.
Read less
Parts Used:
-
George from Morrisville, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!