Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
bake element shorted out, sparking like a sparkler
first, made sure circuit breaker was off second, used nut driver to remove 2 screws on old element, pulled it from the back of the oven third, removed 2 wires from old element (spade connectors) fourth, connected new element and pushed back into oven. fifth, reinstalled 2 screws securing new element
this was all done by my 15 yr old son under my supervision.
The broiler element caught fire and burned out while I was broiling a steak.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches, but I had not turned off the power. So, I shorted out one of the wires. Then I turned off the power but was afraid to go any farther. An appliance repairman was at my house that day fixing my dryer seal. He was able to pull the wires through the insulation successfully and install the broiler element. He did not charge me any extra for this little extra job. But I learned my lesson. Cut the power before you begin! He told me that I could have wound up with a much bigger repair if the short had been in the wire that is connected to the control panel of the oven. I was very lucky!
at first thought the seal would just slide out and the same for the replacement. when I realized that this was not the case and began to wonder what....? I saw the screws at top and bottom, took them off and voila the inner shell moved forward enough to take out the old, slide in the new, push in, replace the screws and back to a happy wife with an oven that can bake correctly again
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.
FIRST MAKE SURE THE OVEN IS OFF!!!! I chose to shut it off at the breaker panel. Remove the two screws that attaches the broiler element to the oven. Gently pull it out. Unplug the two cable wires that are attached. Replace it and install the same way.
bake element burned itself out ( as a welding rod does with all the fireworks)
removed 4 screws of the back fan cover, then removed the two screws holding the element and disconnected the slip-on electrical wire connections. replaced enement and cover in reverse. this was all done after i cut power at circut breaker duhh
TURN OFF ALL POWER TO KITCHEN. Took off all burner coils and plates below them. Lift hood. Locate part. Remove old part and replace with new part in same way as was previously installed. The wire that comes with the kit is actually too much wire, but just arrange it the best you can and leave it....no big deal. I didn't have a magnet, but needed one. The wire from burner coil to switch runs through a harness which is screwed on to the body of the oven (below the range). Be careful NOT to drop it behind oven when taking it out. I dropped it and took forever to get it. That turned a 20 minuate job into an hour and a half. Otherwise this is an easy job that anyone can do. Refrigerator compressor is next. Have fun.
Bake Element Burned Through A Weak Section Of The Tube.
I removed the two mounting screws then pulled the element forward and disconnected the two element screws. I reversed the process to install the new one/ this oven is over 30yrs old.
If I'd had the Nut driver, it would have taken 15 -20 minutes or less. Went to Ace Hardware, bought the nut driver for $4.99.
Turn off the power at the box! Turn off the oven as well. Four screws total. Two to hold it in place and two that connect the element to the source.
First I removed the two screws that hold the element in place. I pulled the element out about 2 inches. Two more screws connect the element wires. I disconnected the element, threw it away, then connected the new element. I put the element in place, then replaced the screws that connect the power. Finally, I replaced the screws that hold the element in place.
Broiler element would not heat; bake element did heat
Removed the oven racks, removed screws holding element hanging support from roof of oven, removed screws holding plate of element to rear of oven. CAREFULLY worked element loose from back of oven and gently alternated pulling each side of element (near the base) until connecting wires came free of insulating batting. Pull too hard and the connecting wires can break loose and disappear behind the batting. Once freed, disconnected both wires with socket (use pliers for extra grip on flat part of connectors, if necessary), removed element, braced new element on bottom of oven, aligning connectors to now-free wires. Re-attached with the new screws that came with the element (attachment points on element are threaded; do not reuse old screws as the threads may not match), gently re-inserted element into insulating batting at rear of oven, reattached hanging support, then replaced element plate screws.
Can be difficult to work in small, deep ovens....many oven doors can be removed. If so, remove oven door and use a chair as a support...lie on your back on the chair and hang your head and arms in the oven.
I removed the screws holding the old element in place, then pulled it out a few inches from the back oven wall. Then I pulled the wires away from the old baking element (pulled off easily), and being careful to keep the wires on the same sides as before, pushed the new element on to the wires. It was then just a matter of inserting the wires and insulation back into the opening and tightening the screws. Simple!
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance