JJW8530DDQ Jenn-Air Wall Oven - Instructions

If doing this for the first time, it's harder to replace than described by others.

Start by removing the oven door. Reach in to unscrew the two screws that hold the sensor in place on the back wall of the oven. I was working on the upper oven of a double wall oven and found it more comfortable to sit on a tall bar stool while working. Pull the sensor partially out and you will see the connector wire running through the sensor opening. The sensor connector plug is too deep into the oven to reach with fingers or any tool. Next unscrew the 6" round heat circulator fan just below the sensor on the back wall of the oven. Pull the fan partially out and you will see the plug for the temp sensor directly behind. You may have to push some of the insulation of out of way. Unplug the old sensor and pull it back out directly through the sensor opening. Take the new sensor and thread it in through the opening and plug it in. Reinstall the circulator fan and then screw the new sensor in place. This should complete the temp sensor replacement.

Removed both oven doors to remove from the wall. Pulled the oven out of the wall. Removed all the sheet metal backing on the back of oven top and bottom. Removed the electrical,connections to the fan. Removed attach,net screws and pulled the fan. A bit of a pain had to twist pull and bend the metal bracket. Replacement fan had to be reversed came apart easily and reversed then reassembled. Fit in easily and attached electrical connections. Then reattached all the sheet metal backing bottom then top. Put oven back in wall then secured in place. Re installed the doors and applied power. Oven worked great as soon as we tested it. Great fix, works better than new!

So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.

Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.

I removed the whole back panel and everything else seemed OK visually.

1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.

2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.

3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.

pull oven, remove back pannel and unplug and remove high limit switch. Repair was the reverse of removal.

The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.

Remove the door, remove screws from all sides

Remove sides and face of oven door by sliding down from under the oven handle trim.

Remove screws on 2nd light of glass and set aside.

Now you are at the inner door panes. their should be two in an insulated type unit.

Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.

Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)

reassemble door as it came apart carefull not to over tighten the screws, they strip easy.

I removed the 2 screws holding the sensor in the back of the oven and pulled the wires out. The connector got hung up in the insulation. Rather than pulling too hard, I loosened up the heating element plate and screws and pulled the whole plate out an inch or so so I could work the connector through the insulation. I forgot to shut off the power. When I put the sensor on, I got the same error. I briefly shut off the power at the breaker and turned it back on. The clock on the oven did not reset. It still didn't work. So I took the whole thing out, shut off the power, reconnected it, turned the power back on, reset the clock, and it worked! Should have turned the power off first and I wouldn't have had to do it twice.

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

I had a service guy come in and he told me the repair would be $550.00. I asked for a part list and did it myself. You guys saved me hundreds of dollars.

I tryed to remove the sensor from the oven by removing the screws inside the oven. Unfortunatly, the plug for the sensor would not reach the inside of the oven. I had to remove the oven from the wall and remove the back cover to ac3ess the sensor wiring.
After that it was a snap.

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

Door fell off so removal of door was easy. Removed screws holding the door together to expose hinges. Removed old hinges that were 3 screws for each hinge. Placed new hinges and installed screws then put door halves back together installed screws and then finally replaced door onto the stove. Mission accomplished

Didn't need sensor replaced. After turning the breaker switch back on oven appeared to be working fine.

Watch the video. Spot on instructions. Easy peasy.

Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.