JGP636WEV7WW General Electric Cooktop - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The porcelain had chipped on the burner bowls
Removed the two screws holding the porcelain burner bowl. Disconected the electric igniter by removing the "w" clip on the underside of the bowl. Then disconnected the igniter from the electric supply cord. Reverse these directions using the new urner bowl.
Really easy.
Really easy.
Parts Used:
-
Paula from Seal Beach, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
14 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner igniter needed to be replaced
Assumed the entire top of the range would have to be lifted off. Removed the three screws inside the top of the over door and then noticed the two screws holding the dish around the burner. They were tight and required WD-40 and then a sharp tap and came off.
Important: Notice the direction your old igniter is plugged into the wire. It is not clear and can go on either way.
Important: Notice the direction your old igniter is plugged into the wire. It is not clear and can go on either way.
Parts Used:
-
Thomas from Bloomsbury, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
37 of 63 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip pans needed to be replaced.
Simiple repair. Determined drip pan size (sm, med., lg.) removed 2 screws holding drip pan, placed gasket around new drip pan and installed. Repaired took less than 5 minutes.
Parts Used:
-
Steve from Broken Arrow, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
18 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacement cook-top, had natural gas orifices, needed propane
Three were simple screw out and replace with a nut driver. The warming burner had a smaller opeining which was too large for the nut driver. Had to remove shielding aroound it first. Simple, job. My mother did the last one.
Parts Used:
-
Aloha from Monterey, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
9 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner bowl worn out from cleaning
Pulled off burner grates, burner, unscrewed burner bowl, removed clip from igniter and wire, then put it all back together. Was very easy, and the stove looks like new again.
PartSelect is very good with amazing shipment times. The kjpart arrived much sooner than expected.
PartSelect is very good with amazing shipment times. The kjpart arrived much sooner than expected.
Parts Used:
-
Leon from Lancaster, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner bowl mounting holes out of alignment
No way to adjust mixer tube assembly so the mounting holes will line up with the holes in the burner bowl. Mounting
holes in bowl should be slotted to prevent future problems.
Had to finally bend the mixer tube mounting bracket enough to get one bowl on. It also made the procelin break
on that bowl because the screw put to much pressure on the side of the hole.
Igighter mounting hole out of position just enough to prevent the burner head from sliding over it and sitting on
the mixer tube correctly.
I solved this problem by fileing the opening slot for the igniter. Even with the igniters being just a little out of
alignment from the original position they still light well.
I did not get new gaskets for the burner bowl but would reccommend that you get them.
holes in bowl should be slotted to prevent future problems.
Had to finally bend the mixer tube mounting bracket enough to get one bowl on. It also made the procelin break
on that bowl because the screw put to much pressure on the side of the hole.
Igighter mounting hole out of position just enough to prevent the burner head from sliding over it and sitting on
the mixer tube correctly.
I solved this problem by fileing the opening slot for the igniter. Even with the igniters being just a little out of
alignment from the original position they still light well.
I did not get new gaskets for the burner bowl but would reccommend that you get them.
Parts Used:
-
Keith from Frisco, TX
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Electrode ceramic insulator was cracked
First I elevated range top, then removed cracked electride from connector pin. Installed new electrode and lowered range top and all was fine.
Parts Used:
-
Robert from Irvine, KY
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
4 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No Spin Cycle
Lid Switch.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.
Parts Used:
-
Richard from LORDSBURG, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Scratches in drip pan from improper cleaning, spills during cooking.
The replacement part not right size for the porcelain cone for gas. Had to unscrew 2 screws remove the cone, after unclicking gas wire. The gas spreader did not fit with the cone in place.
Parts Used:
-
Sara from AURORA, IL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bottom Heating element quit working after 30 years
Removed several screws and removed element. Replaced same. Total ten minutes.
Parts Used:
-
Harry from Dills burg, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Failed ignition switch
took me a a while to find my problem. One burner would not spark to ignite gas burner. From Part Select website I noticed the part that was the problem from the parts diagram. I did not realize it was related to ignition until I saw that. Easy and cheap to fix after that.
Parts Used:
-
wally from lake oswego, OR
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers
6 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
worn burner bowl.
I received a defective part from PartsSelect.com. After contacting their Customer Service, they promptly replaced the part for no charge at all. I am very, very pleased with PartsSelect.com and recommend them to all "home mechanics".
The bowl was replaced by removing two screws, removing the igniter wire, clip, and igniter. Reverse to re-assemble. I would recommend replacing the gasket at the same time.
The bowl was replaced by removing two screws, removing the igniter wire, clip, and igniter. Reverse to re-assemble. I would recommend replacing the gasket at the same time.
Parts Used:
-
Leon from Lancaster, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The burner bowls were discolored
Real simple to do. Simply remove the two screws holding the bowl and disconnect the electric wire. Obviously first pull the power cord to prevent being shocked.
Re-attach the power cord and and screw the bowl tight. Plug in the power cord.
Re-attach the power cord and and screw the bowl tight. Plug in the power cord.
Parts Used:
-
George from mission viejo, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner would not light
-
Jimiego from San Diego, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
7 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
would not ignite
It was so easy.I removed the old part with the new with pliers. Voila/// it worked.
Parts Used:
-
Terry from Longmont, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers, Screw drivers
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!